Publicidad
WARRANTY
LIMITED WARRANTY Fellowes, Inc. ("Fellowes") warrants the cutting blades of the machine to be free from
defects in material and workmanship for 7 years from the date of purchase by the original consumer.
Fellowes warrants all other parts of the machine to be free of defects in material and workmanship for
2 years from the date of purchase by the original consumer. If any part is found to be defective during
the warranty period, your sole and exclusive remedy will be repair or replacement, at Fellowes' option
and expense, of the defective part. This warranty does not apply in cases of abuse, mishandling, or
unauthorized repair. ANY IMPLIED WARRANTY, INCLUDING THAT OF MERCHANTABILITY OR FITNESS
FOR A PARTICULAR PURPOSE, IS HEREBY LIMITED IN DURATION TO THE APPROPRIATE WARRANTY
6
MS-470Ci_404156_REVB_ENG_091109.indd 5-6
MS-470Ci_404156_REVB_ENG_091109.indd 5-6
All manuals and user guides at all-guides.com
PERIOD SET FORTH ABOVE. In no event shall Fellowes be liable for any consequential or incidental
damages attributable to this product. This warranty gives you specific legal rights. The duration, terms,
and conditions of this warranty are valid worldwide, except where different limitations, restrictions, or
conditions may be required by local law. For more details or to obtain service under this warranty, please
contact us or your dealer.
JAM PROOF SYSTEM OPERATION*
Eliminates frustrating jams by preventing overloads and powering through misfed paper.
Advanced Jam Prevention- Electronically
1
measures paper thickness to prevent paper jams:
Up to RED: Too many
sheets have been inserted.
Up to YELLOW: Productivity
is optimized.
Up to GREEN: More sheets
can be added.
If a misfeed
All indicators light up and
occurs:
shredder pauses for 3-6 seconds
*100% Jam Proof when used in accordance with user manual
SLEEP MODE
WHEN IN SLEEP MODE
2
1
3
AUTO
To get out of sleep mode
In sleep mode
or
insert paper
touch control panel
BASIC PRODUCT MAINTENANCE AND TROUBLESHOOTING
OILING SHREDDER
CLEANING AUTO-START INFRARED SENSORS
All micro-cut shredders require oil for peak performance. If not oiled, a
Paper detection sensors are designed for maintenance free operation. However, on rare occasions the sensors
machine may experience diminished sheet capacity, intrusive noise when
may become blocked by paper dust causing the motor to run even if there is no paper present.
shredding and could ultimately stop running. To avoid these problems, we
(Note: two paper detection sensors are located in the center of the paper entry)
recommend you oil your shredder each time you empty your waste bin.
FOLLOW OILING PROCEDURE BELOW AND REPEAT TWICE
1
2
3
AUTO
AUTO
*Apply oil across entry
Turn off and unplug
Press and hold reverse
shredder
(
) 2-3 seconds
*Only use a non-aerosol vegetable oil in long nozzle container such as Fellowes 35250
PREVENTIVE MAINTENANCE AND MISCELLANEOUS TROUBLESHOOTING
• Self Cleaning Cycle: Shredder periodically cycles in forward and reverse lasting 3-6 seconds
• Empty wastebasket when bin full indicator lights up.
• Shredder won't run if the door is open, or bin needs to be emptied. Bin must be in machine, with door closed, in order for machine to operate properly.
• Maintenance is an important part of protecting your investment. Don't forget our oil (35250) and shredder bags (36054).
Go to Support Section at www.fellowes.com or see back page of manual for useful telephone numbers.
2
3
Remove several sheets until
indicator is below red.
Continue 100% Jam
Proof Shredding
If
illuminates after paper has been
Wait for flashing to stop after automatic correction
reversed, press reverse and remove paper.
is complete. Regular shredding will resume.
Otherwise, regular shredding will resume.
SAFESENSE
®
TECHNOLOGY OPERATION
SET-UP AND TESTING
1
2
3
4
AUTO
Turn the shredder ON
Touch test area and
SafeSense
is active and
If hand is held on SafeSense
®
( ) to activate SafeSense
look for the SafeSense
working properly
area more than 2 seconds
®
®
indicator to illuminate
shredder will shut off
.
TO CLEAN THE SENSORS
1
2
3
4
AUTO
Turn off and unplug
Locate Auto-start
Dip cotton swab in
Using cotton swab, wipe
shredder
infared sensor
rubbing alcohol
away any contamination
from the paper sensors
®
3
9/15/09 3:16:42 PM
9/15/09 3:16:42 PM
Publicidad
