Martinelli MILANO Navetta XL Manual De Instrucciones página 19

the child with greater protection from the elements.
Unfasten the cover at the sides (arrow_a), fold it up (arrow_
b) and fasten it to the hood with the Velcro (arrow_c).
5• HANDLE: Rotate the handle upwards until it clicks into
place (arrow_a). The handle is only locked in place when
it is in the vertical position. To lower the handle, press the
two round buttons at the same time (arrow_b) and rotate it
downwards (arrow_c). The handle is useful for carrying the
Navetta XL (fig_d) and for fitting it to chassis and strollers.
6• ROCKING POSITION: The base of the Navetta XL has a
special shape which allows you to rock the child when it is
placed on a flat surface.
7• COT POSITION: It is possible to make the Navetta XL into
a non-rocking cot by opening out the two legs under the
base.
8• ADJUSTING THE BACKREST and THE FOOTREST: with the
COMFORT SYSTEM, backrest and footrest can be adjusted
simultaneously. Pull the knob outwards (fig_a) while
turning it (fig_b) to raise or lower the backrest and the
footrest.
9• FOUR SEASONS SYSTEM: There are holes under the base of
the Navetta XL which can be opened or closed to adjust
the air circulation inside it.
To open the holes, move the 4 levers outwards.
Ganciomatic System
1 0• Ganciomatic is the quick, practical system that allows you
to attach the Navetta XL to the Ganciomatic clips of a
stroller or the base of a chassis.
To attach the Navetta XL, put it on the stroller or the
chassis and press with both hands until it clicks into place.
Always apply the brakes on the stroller or chassis before
attaching and removing the Navetta XL.
Check that the bassinet unit is properly attached.
1 1• To release the Navetta XL, lift the Ganciomatic lever on the
back (arrow_a) and pick the product up with the handle
(arrow_b).
Removing the lining
1 2• REMOVING THE LINING OF THE Navetta XL: Unbutton the
hood on the sides and the back (fig_a), press down on the
All manuals and user guides at all-guides.com
1 3• Unbutton the cover and remove it (fig. c). Unbutton the
1 4• There are two pockets at the end of the Navetta XL by the
How to fit the safety harness
1 5• Put the Navetta XL in the car with the backrest and the
1 6• When travelling in vehicles, remove any additional mattress
1 7• 3-POINT SAFETY HARNESS: Pass the leg divider straps
1 8• Pass the two ends of the shoulder straps through the slots
1 9• Check that the straps are correctly fastened under the shell
ATTACHING THE Navetta XL IN CARS: It is possible to install
We recommend positioning the bassinet unit on the
2 0• The Navetta XL positioned in a car with a lap belt.
2 1• The Navetta XL positioned in a car with a 3-point belt.
2 2• The Navetta XL can also be positioned in the centre of a
19
clips to release them (fig_b) and pull the hood upwards to
remove it.
covering on the sides and raise the backrest to lift it (fig. d),
then pull upwards to remove the covering (fig. e).
child's feet. Keep the instruction manual in one and the car
kit straps in the other.
Car kit
hood lowered and the handle raised.
pads.
through the slot in the mattress pad (fig_a) and the slots
in the shell (fig_b) so that they come out on the other side
(fig_c).
in the mattress pad and the shell (fig_a), then clip them to
the pins (fig_b).
(fig_a) and inside the Navetta XL (fig_b).
Attachment in vehicles with safety belts
the bassinet unit in cars if there are 3 rear seats with 3 safety
belts. The central one can be 3-point or a lap belt.
vehicle's rear seats with the end for the child's head above
the central seat.
3-person rear seat, using the two outer safety belts (fig_a).
It cannot be positioned as in fig_b because it can only be
secured in cars using safety belts that come from opposite
sides.