Controls And Functions; Tone Arm Assembly - Akiyama DX-101 USB-R Manual Del Usuario

CONTROLS AND FUNCTIONS

. DX-101 USB & DX-101 USB-R
1
START/STOP
Press this button to start or stop the platter.
2
PLATTER
3
MOTOR OFF
Press the button to enable motor off, and the led will be flash .
Press the button again to disable function.
4
TARGET LIGHT
Insert target light to the deck and it will light up.
5
PLATTER REVOLUTION SPEEDS (rpm)
33 rpm Press 33
45 rpm Press 45
(Only DX-101 USB) 78 rpm Press 33 and 45 buttons
simultaneously. To return to 33 or 45rpm play mode just press the
desired button.
6
REVERSE
This button is used to reverse the direction of the platter rotation.
7
HEAD SHELL LOCKING NUT
Attach the headshell by inserting into the front end of the tone arm,
then turn the locking nut clockwise with the head shell firmly held
horizontally.
8
PITCH SLIDER
Use this to change the speed of the platter when the PITCH
indicator is NOT lit.
9
TONE ARM
This is a fully manual tone arm. To start playback, gently place
the stylus on the record using the headshell finger support. Do
not drop the stylus onto the record as it may cause damage to the
diamond tip and to the record.
10
45 RPM ADAPTOR
Place on center spindle for playing 7" records with large center
holes.
11
ANTI SKATE KNOB
When a record is playing, a force is generated drawing the stylus
towards the center of the record. Set this knob to the same value as
the stylus pressure to offset this force.
12
COUNTERWEIGHT
Use this to balance the tone arm and to adjust the stylus pressure.
13
POWER SWITCH
This switch turns the power on or off, including the motor and
audio signal
14
POWER CORD CONNECTOR
Used to connect the included power cord.
15
USB CONNECTOR
USB connection (USB cable limit within 3M).
16
PHONO/LINE SWITCH
This is a switchable 'phono level' or 'line level' output (using RCA
jacks) which can be connected to the 'phono' or 'line' input on an
3
All manuals and user guides at all-guides.com
exterior unit.
17
OUTPUT L& R
This is the standard analog output (RCA jacks) which can be
connected either to a phono or line input on any DJ mixer,
depending on the setting of the phono / line selector.

TONE ARM ASSEMBLY

7
HEADSHELL - Install cartridge here. When installing a
cartridge, refer to the installation instructions supplied by the
manufacturer of that cartridge. During installation, attach the
stylus protector to guard the stylus tip from damage.
Attach wires as follows:
White (L+) Left channel+
Blue (L-) Left channel -
Red (R+) Right channel+
Green (R-) Right channel-
9
S-SHAPED TONEARM
18
TONEARM LEVER
Controls the up and down action of the tone arm lift.
11
ANTI-SKATE CONTROL
tone arm so it doesn't skip outward across the record due to the
centrifugal force of the record spinning. Cartridge manufacturers
usually specify the proper setting of this.
12
11
18
12
COUNTERWEIGHT
downward pressure of the stylus to the record. Attach now by
sliding the counterweight onto the rear of the tone arm. Twist it
9
lightly and it will screw onto the rear shaft of the tone arm.
a. Remove the stylus protective cover, if so equipped. Never touch
the stylus tip during the adjustment.
b. Lower the tonearm lever.
c. Release the tonearm clamp and release the tonearm from the arm
rest.
d. Set the anti-skate adjustment to zero
e. Rotate the counterweight in either direction until the tonearm is
perfectly balanced horizontally (floats freely).
f. Return the tonearm to the arm rest and lock it in place.
g. Hold the counterweight stationary with one hand and rotate only
the stylus pressure ring to bring the number "0" of the ring into
alignment with the center line on the tonearm rear shaft.
h. Rotate the counterweight clockwise until the scale value
corresponding to the recommend stylus pressure
Note: The recommended stylus pressure of the optional cartridge
that may have been includ-ed with your unit is 2 grams. For all
7
other cartridge systems please refer to the manufactures
specification included with the cartridge.
19
USB SOCKET
Connect a USB Pen Drive or HDD to record your vinyl, info will
stored in MP3 format only.
20
PLATTER SPEEDS
Select between 33 rpm & 45 rpm using the appropiate knobs.
21
RECORD/STOPBUTTON
Press the button to start recording and press again to stop
recording.
This applies inward force to the
Adjustment creates the proper
DX-101 USB-R