D&D Technologies Z-Lokk ZL1 Instrucciones De Instalación

INSTALLATION INSTRUCTIONS
The Z•LOKK™ is designed to fit gate frames of up to 1
thicknesses are supplied to assist mounting - see matrix chart below. This lock is not recommended for child safety gates;
use Magna-Latch magnetic safety gate latches for these applications, and consult the appropriate local authorities
®
regarding any local fence/barrier code regulations and requirements.
Tools: Electric or cordless drill (for self-drilling screws only),
gates, Phillips No. 2 screwdriver (for self-tapping screws).
Installation Procedure
1.
Note: The gap between the Fence
Post and the Gate Frame must be
between 3 " (10mm) and 1 1 "
/ /
8 4
(31mm). Determine the desired
location of the lock (i.e. Lock
Body) on the Gate Frame. If
required, use one of the Spacers
supplied (see matrix chart
below) to provide a neat finish of the
Latch Body against the Gate Frame.
Remove screws "D" (obscured), insert
spacer and replace screws "D".
2.
(Always predrill metal using the
5 " (4mm) drillbit.) Using four of
/
32
the 1"x10g wafer-head, self-drilling
screws supplied ["A"], fix the Lock
Body onto the Gate Frame (see Fig 1.)
3.
The Lock Tail (located inside the
Lock Cover) and the slot in the Rotor
must both be horizontal to the ground
so that when assembling the Lock
Cover onto the Lock Body the Lock Tail
will slide into the corresponding slot in the Rotor. If the Lock Tail is not horizontal, use needle-nosed pliers and turn it 90˚ until it's in the horizontal position.
If the slot in the Rotor is not horizontal, turn the Rotor 90˚ with your fingers until the slot is horizontal (see Fig. 2).
4.
Place the Lock Cover straight onto and directly over the Lock Body (not at an angle) ensuring that the "Lock Tail" bar (see Figure 2) is inserted horizontally
into the corresponding slot within the molded rotor. Important: Once the Latch Cover is firmly in place, carefully insert the two longest screws ["B"] at a 90˚
angle using a power drill...however, do not tighten fully with the power drill. Complete the insertion of the screws using a hand screwdriver. DO NOT over-
tighten the screws. Check that the handles move freely and in unison.
5.
Take the Keeper and align it on the post so that it is centered on the Lock (Figure 1), as shown by the dashed line. Holding the Keeper in position, take the
three remaining 1"x10g wafer-head, self-drilling screws and fix it to the fence post. For best results, mount all these screws in the center of the adjustment slots.
6.
Using the hand screwdriver, insert it into the Adjustment Screw "C" (obscured) between the Keeper and its mounting bracket. Adjust the screw horizontally, as
required, so that the gate closes and locks smoothly. Note that the minimum gap between Keeper and Lock is desirable. The Keeper should be adjusted so that the
maximum gap is no greater than
Open and close the gate to check that the lock operates correctly. Adjust the Keeper as necessary at any time to ensure safe operation of the lock.
NOTE: For future vertical adjustment of the Keeper, open gate and adjust Keeper horizontally to reveal the
screw on the fence post. Loosen all three screws on the post and adjust Keeper to the desired vertical position.
Re-tighten all screws and re-adjust the Keeper horizontally so the
MAINTENANCE: REMOVE KEYS FROM LOCKS AFTER USE.
any time; use only powdered graphite. Ensure all screws are tightened firmly and that the Lock is kept free of dirt,
sand and other debris which could impair reliable performance. Re-adjust Keeper as necessary to ensure effective
operation.
WARRANTY & LIMITATION OF LIABILITY
D&D Technologies' ("D&D") products are warranted to be free of defects in materials and workmanship to the original purchaser
for as long as he/she owns the product. This product will operate properly, and warranty is valid, only if installed in accordance with
the instructions and specifications shown. If a structural defect appears, the original purchaser may return the item, freight prepaid,
together with proof of purchase to D&D or its approved international agents. D&D or its agent will, at their discretion, repair or
replace the defective item or part without charge to the purchaser. THIS WARRANTY SHALL NOT APPLY WHEN the product has been
tampered with, when repairs or attempted repairs have been made by unauthorized persons, where the item has been subjected
to misuse, abuse, accident or damage in transit, or where the installer has not followed the instructions set out during installation,
operations, or Maintenance Requirements. IN NO EVENT
SHALL THE COMPANY BE LIABLE FOR ANY INCIDENTAL OR
CONSEQUENTIAL DAMAGES. No warranty is given other
than that set out above. No other express or implied war-
ranties (including statutory warranties) apply, other than
warranties which may not be legally excluded.
/ " (41mm) or 2
5
8
/ " [4mm] drillbit for predrilling metal posts/
5
32
Adjustment Screw
is located between
Keeper and its
mounting bracket
A
KEEPER
3 " (10mm) between the edge of the Keeper and the edge of the Lock Body.
/
8
3
Do not lubricate this lock with petroleum-based lubricants at
- for Metal Picket Gates
/ " (63mm) wide. Spacers of different
1
2
C
A
A
B
A
A
LOCK
B
BODY
FIGURE 1
" maximum distance is achieved.
/
8
www.ddtechglobal.com
USA: 7731 Woodwind Drive, Huntington Beach, CA 92647. Tel (800) 716-0888.
AUSTRALIA: U6, 4-6 Aquatic Dr, Frenchs Forest NSW 2086. Tel (02) 9975 4500
Two screws
D
A
A
LOCK
COVER
Supplied
Spacer
–
1 "/3mm
/
8
3 "/10mm
/
8
5 "/16mm
/
8
Supplied
Spacer
–
1 "/13mm
/
2
3 "/19mm
/
4
LB000000019PA
ROTOR
ROTOR
Lock Tail.
Keep flat.
FIGURE 2
Gate Frame Min. Distance
Width to 1st Picket
5 "/41mm 5 "/41mm
1 1
/ /
8 8
1 "/38mm 3 "/44mm
1 1
/ /
2 4
1 "/32mm "/50mm
1 2
/
4
"/25mm 1 "/57mm
1 2
/
4
Gate Frame Min. Distance
Width to 1st Picket
"/63mm "/41mm
1 5
2 1
/ /
2 8
"/50mm 1 "/54mm
2 2
/
8
3 "/44mm 3 "/60mm
1 2
/ /
4 8
•instr_zlokk_27/3/07