Electronic Baby Monitor; Baby Unit - BabyOno 198 Manual De Instrucciones

GB

Electronic baby monitor

1. Aerial
2. Baby unit on/off switch
3. Parent unit on/off switch
4. Baby unit power led / green
Low battery or out of range signalling led / orange
5. Parent unit power led / green
Low battery or out of range signalling led / orange
6. Volume level indicator led
7. Speaker
8. Belt clip
9. Speaker on/off switch
10. Parent and baby unit volume intensity control
11. Mains power adapter socket
12. Pairing baby and parent units
13. On/off switch - reset
5. 7. 9.10. 1. 8.
3. 6. 12. 11. 13.
4. 7. 10. 1.
2. 12. 11. 13.
2
All manuals and user guides at all-guides.com
Babyono electronic monitor is a portable monitoring system.
• Bidirectional transmission (Walkie-Talkie)
• Wireless, digital transmission 2.4GHz.
• High sensitivity
• Stand-by (VOX) power saving mode
• Alkaline batteries AAA 8x1.5V (optional)
• Mains power adapters included (2 pieces)
• Range up to 300 meters in open space
• Belt-clip to carry the monitor around the house
• 32 channels ensuring disturbance-free operation
(FHSS)
MONTAGE
Place the baby unit app. 1 meter away from the child. Con-
nect the mains power adapter to the baby unit adapter sock-
et or install the batteries (4 x 1.5V AAA). Press the ON/OFF
switch to switch on the device. The power LED will turn green.
To switch off the device, press the ON/OFF switch and hold it
for 3 seconds. The volume intensity level of the baby unit may
be adjusted by using +/-. Connect the mains power adapter
to the parent unit adapter socket or install the batteries (4
x 1.5V AAA). The LEDs indicate the volume intensity level.
Parents can talk to children when simultaneously pressing
and holding the speaker ON/OFF switch. Release the switch
to hear the child's voice again.
PAIRING
In case the signal level is very low, you may change the chan-
nel by pressing the „Pair" button in both the devices. Press the
"Pair" buttons in both the devices and hold them for app. 1
second. The units will search for a disturbance-free channel
to continue operation. In order to avoid acoustic feedback,
make sure that the minimum distance between the units is
2 metres.
HOW TO EXCHANGE THE BATTERIES - 8 x 1.5V (AAA)
1. Unscrew the battery compartment cover and place
the batteries as indicated (pole marking).
2. Place the cover in its original position, screw it down
and make sure it has been properly mounted.
3. Switch on the device and check if the LED has turned
green.
4. The battery life depends on their power and the
intensity of operation; which may be from 10 hours
to a couple of days.
LOW BATTERY LEVEL INDICATOR
When the battery is low, the green LED turns into orange. In
that case, exchange all the batteries in a given device as soon
as possible. For long operation, using mains power adapters
instead of batteries is recommended.
IMPORTANT!
Remove the batteries before connecting the mains power
adapters!
The units should be connected to DC5V socket.
SOUND WARNING SIGNALS GENERATED
BY BABY AND PARENT UNITS
If the parent unit is place too far away from the baby unit,
the system may not operate properly. In this case, a "beep
beep" sound informing that the parent unit has lost contact
with the baby unit will be generated. Simultaneously, the
three LEDs will be flashing. Place the parent unit closer to
the baby unit.
If the parent unit is placed too close to the baby unit (less
than 2 metres), acoustic feedback can occur. In this case,
place the devices farther away from each other or decrease
the volume of the parent unit.
The „beep beep" sound signal may also indicate low battery
level in the other device. In case the main LED has turned or-
ange, exchange the batteries. The "beep beep" sound signal
will also be generated by the parent unit once the baby unit
has been switched off.
SAFETY
For your own safety, use the original mains power adapters
only.
To minimise the risk of fire or electrocution, do not expose the
device to rain or moisture.
Connect the device to a socket located within easy reach. In
case any malfunctioning is detected, disconnect the device
immediately from the socket.
To avoid electrocution, never open the cover of the devices.
Do not use damaged mains power adapters.
WARNING!
Batteries may be exchanged by an adult person only.
1. Place the batteries into the battery compartment as
indicated (pole marking).
2. Batteries not fit for recharging must not be re-
charged.
3. Rechargeable batteries may be recharged by an
adult person only.
4. Rechargeable batteries must first be removed from
the devices.
5. Different battery types, or new and old batteries
must not be mixed.
6. Only the recommended or equivalent battery types
may be used.
7. Used batteries must immediately be removed from
the device.
8. Power terminals must not be short cut.
9. Neither the baby unit nor the parent unit may be
connected to more power supply sources than rec-
ommended.
10. Used batteries must be disposed
of at specially marked containers
for used batteries, small electronic
equipment and household appli-
ances.
TECHNICAL SPECIFICATIONS

BABY UNIT

Frequency of transmission: 2400MHz-2480MHz
Power transmission: 17dBm
Range (in open space): 300M
Operating temperature: 0 °C - 50 °C
Storage temperature 25 °C
Moisture operation level: 20% -80% RH
Power consumption: min. 25mA, max. 125mA
Power supply: DC5V 1000mA
PARENT UNIT
Frequency of transmission: 2400MHz-2480MHz
Power transmission: 17dBm
Range (in open space): 300M
Operating temperature: 0 °C - 50 °C
Storage temperature: 25 °C
Moisture operation level: 20% -80% RH
Audio out: 300mW
Power consumption: min. 50mA, max. 240mA
Power supply: DC5V 1000mA
Sensitivity: -88dBm
3