Publicidad
4
3
2
high
1
low
FUNCTIONS
0
input
4
3
2
high
1
low
0
input
1
2
WARNING: THIS APPLIANCE MUST BE EARTHED
KETTLESTRING LANE | YORK | YO30 4XF | UNITED KINGDOM
METALLVÄGEN 45A | 195 72 ROSERSBERG | STOCKHOLM | SVERIGE
LAHNSTRAßE 27 | 45478 MÜLHEIM AN DER RUHR | DEUTSCHLAND
INPUT POWER: 220-240VAC, 50-60Hz
FUSE: 250V F1.6A
SERIAL NO.:
POWER CONSUMPTION: 50W MAX
12
WARNING: THIS APPLIANCE MUST BE EARTHED
1. INPUT CONNECTOR
KETTLESTRING LANE | YORK | YO30 4XF | UNITED KINGDOM
METALLVÄGEN 45A | 195 72 ROSERSBERG | STOCKHOLM | SVERIGE
LAHNSTRAßE 27 | 45478 MÜLHEIM AN DER RUHR | DEUTSCHLAND
Connect your guitar to this connector using a
6.3mm TS jack cable.
INPUT POWER: 220-240VAC, 50-60Hz
FUSE: 250V F1.6A
SERIAL NO.:
POWER CONSUMPTION: 50W MAX
2. HIGH/LOW SWITCH
Switch between 1W (low) and 15W (high) power
output using this switch.
3. REVERB CONTROL
Adjust this dial to control the amount of reverb
is added to the output signal. Turning fully
anticlockwise will add no reverb to the output
signal.
4. TREBLE CONTROL
Adjust this dial to control the amount of treble
(high frequency) sent to the speaker output.
5. MIDDLE CONTROL
Adjust this dial to control the amount of mid-
range frequency sent to the speaker output.
6. BASS CONTROL
Adjust this dial to control the amount of bass
(low frequency) sent to the speaker output.
7. SHAPE CONTROL
Adjust the tone of your amplifier using this dial.
Fully anticlockwise will produce a thinner sound,
fully clockwise will produce a broader sound.
8. VOLUME CONTROL
Adjust this dial to control the overall volume sent
to the speaker output connector on the rear of
the amplifier.
9. GAIN CONTROL
Adjust this dial to increase the input gain from
the guitar. More gain will create a more distorted
sound.
reverb
treble
middle
5
5
5
6
4
6
4
6
7
3
7
3
8
2
8
2
9
1
9
1
10
0
10
0
10
reverb
treble
middle
5
5
5
6
4
6
4
6
7
3
7
3
8
2
8
2
9
1
9
1
10
0
10
0
10
3
4
5
CAUTION
RISK OF ELECTRIC SHOCK
DISCONNECT INPUT POWER
BEFORE OPENING. Ta=40°C
WWW.GEAR4MUSIC.COM
MADE IN CHINA
reverb
footswitch
CAUTION
RISK OF ELECTRIC SHOCK
DISCONNECT INPUT POWER
BEFORE OPENING. Ta=40°C
WWW.GEAR4MUSIC.COM
MADE IN CHINA
reverb
footswitch
bass
shape
5
0
4
6
7
3
7
3
8
2
8
2
9
1
9
1
0
10
10
10
bass
shape
5
0
4
6
7
3
7
3
8
2
8
2
9
1
9
1
0
10
10
10
6
7
return
effects loop
effects loop
13
14
return
10. STANDBY LIGHT
This light will illuminate when the amplifier is
switched on.
effects loop
effects loop
11. POWER SWITCH
This switch turns the amplifier on and off. When
the amplifier is switched on, allow a moment for
the tubes to warm up before playing. This will
increase the lifespan of the tubes and create a
better output sound.
12. MAINS POWER CONNECTOR
Connect the amplifier to the mains power
using this connector. Only use the mains cable
provided with the product.
13. REVERB FOOTSWITCH CONNECTOR
Connect a one button footswitch with a 6.3mm
TS jack cable to this connector (not included) to
turn the reverb on and off remotely.
14. EFFECTS LOOP (RETURN) CONNECTOR
Connect the output of an external effects
processor to this connector using a 6.3mm TS
jack cable.
15. EFFECTS LOOP (SEND) CONNECTOR
Connect the input of an external effects
processor to this connector using a 6.3mm TS
jack cable.
16. SPEAKER OUT CONNECTOR
Connect an external speaker to this connector
using a 6.3mm TS speaker jack cable.
NOTE This connection outputs at an amplifier level.
It is recommended to use a speaker jack cable
capable of carrying the required load.
3
volume
gain
5
5
4
6
4
6
7
3
7
8
2
8
9
1
9
0
10
0
10
standby
volume
gain
5
5
4
6
4
6
7
3
7
8
2
8
9
1
9
0
10
0
10
standby
8
9
10
send
speaker
output
15
16
send
speaker
output
11
Publicidad
