Brute 2500 PSI Guia De Inicio Rapido

WARNING Failure to read and follow the operator's
manual and all operating instructions could
result in death, serious injury, and/or property
damage.
WARNING Fuel and its vapors are extremely
flammable and explosive which could cause
burns, fire or explosion resulting in death,
serious injury and/or property damage. Turn
pressure washer engine OFF and let it cool at least
2 minutes before removing fuel cap. Let spilled fuel
evaporate before starting engine. Always allow space for
fuel expansion.
WARNING Starter cord kickback (rapid retraction)
will pull hand and arm toward engine faster
than you can let go which could cause broken
bones, fractures, bruises, or sprains resulting
in serious injury. NEVER pull starter cord without first
relieving spray gun pressure. Pull starter cord slowly
until resistance is felt, then pull rapidly. Firmly grasp
spray gun with both hands when using high pressure
spray to avoid injury when spray gun kicks back.
You will need:
• Utility knife • Unleaded fuel • Garden hose, 50 feet (15 m) or less
Unpack pressure washer
1. Remove everything from carton except pressure washer.
2. Ensure you have all included items prior to assembly.
If items are damaged or missing, call 1-800-743-4115.
3. Open carton completely by cutting each corner from top to bottom.
4. Prior to assembly, lubricate all o-ring connections as described in
operator's manual.
Attach handle and accessory tray
1. Place handle (A) onto base. Make sure holes in handle align with
holes on base.
1
2. Insert carriage bolts (B) through holes from outside of unit and
attach a plastic knob (C) from inside of unit. Tighten by hand.
3. Place accessory tray (D) over base (viewing from rear of unit). Make
sure holes in accessory tray align with holes on base. Push the tree
clips (E) into the holes until they sit flat against the accessory tray.
4. Place spray gun (F) through hole on accessory tray on left side of
unit, place nozzle extension (G) through hole on accessory tray, as
shown.
3
5. Hang high pressure hose (H) on accessory tray as shown.
Add engine oil and fuel
NOTICE You MUST properly fill engine with oil before attempting to start
pressure washer.
NOTICE DO NOT use E85 fuel.
NOTICE DO NOT mix oil with fuel.
1. Move pressure washer outdoors to a flat, level surface.
2. Clean area around oil fill and remove yellow oil fill
cap/dipstick ( ).
4
3. Using oil funnel (optional), slowly pour contents of provided oil
bottle into oil fill opening.
4. Replace oil fill cap/dipstick and fully tighten.
5. Clean area around fuel fill cap, remove cap (
6. Slowly add regular UNLEADED fuel to fuel tank. Be careful not to
overfill. Allow about 1.5" (4 cm) (J) of tank space for fuel
expansion.
5
7. Install fuel cap and let any spilled fuel evaporate before starting
engine.
TM
© 2012 Briggs & Stratton Corporation. All rights reserved. BRUTE is a trademark of Briggs & Stratton Power Products Group, LLC.
Every effort has been made to ensure that the information in this document is accurate and correct. However, we reserve the right to alter or otherwise improve the product and this document at any time without prior notice and without incurring obligation.
*This pressure washer is rated in accordance to the Pressure Washer Manufacturers Association (PWMA) standard PW101 (Testing and Rating Performance of Pressure Washers).
Quick Start Guide
2500 PSI @ 2.0 GPM / 2000 PSI @ 2.3 GPM*
WARNING Running engine gives off carbon
monoxide, an odorless, colorless, poison
gas. Breathing carbon monoxide could result
in death, serious injury, nausea or fainting.
Operate this product ONLY outdoors. DO NOT operate
this product inside any building or enclosure, even if
windows and doors are open.
WARNING High water pressure could cut through
skin resulting in serious injury. Spray gun
traps high water pressure, even when engine
is stopped and water is disconnected. NEVER
aim spray gun at people, animals, or plants. ALWAYS
point spray gun in safe direction, press red button and
squeeze spray gun trigger to release high pressure,
every time you stop engine.
WARNING Risk of eye injury. Spray could splash
back or propel objects resulting in serious
injury. Always wear indirect vented (chemical
splash) safety goggles marked to comply with
ANSI Z87.1 when using or in vicinity of this equipment.
NEVER substitute safety glasses or dry-condition
goggles for indirect vented safety goggles.
Items Included:
Operator's Manual (not shown)
• Safety goggles (indirect vented type)
1
A
B
C
1
2
2
3
3
F
H
4
).
4
5
J
Pressure Washer
Move pressure washer
to safe operating location
WARNING Outdoor use ONLY. DO NOT start or run engine indoors
or in an enclosed area, even if windows and doors are open.
Running engines give off carbon monoxide, an odorless,
poison gas that can cause nausea, fainting or death.
1. Move pressure washer outdoors to a flat, level surface. Running
engines give off carbon monoxide.
2. Keep at least 5 ft. (1.5 m) clearance on all sides of pressure washer
including overhead to reduce the risk of exhaust heat or exhaust
gases igniting nearby combustible material.
Connect spray gun
NOTICE Remove and discard 2 shipping caps from high pressure outlet
and garden hose inlet connections.
1. Uncoil high pressure hose (H) and attach one end of hose to base of
spray gun (F). Tighten by hand.
2. Attach other end of high pressure hose (H) to high pressure outlet
(K) on pump. Tighten by hand.
Connect water supply
NOTICE If inlet screen is damaged or missing, DO NOT use pressure
washer, call 1-800-743-4115.
1. Inspect garden hose inlet screen (M) for damage.
2. Clean screen if it contains debris or have it replaced if damaged.
3. Run cold water through garden hose for 30 seconds to clean out any
debris. Garden hose length must not exceed 50 feet (15 m). Turn
off water supply and attach garden hose (N) to water inlet. Tighten by
hand.
9
Start pressure washer
NOTICE You MUST connect and turn on water supply fully before
starting engine.
WARNING Risk of eye injury. Spray could splash back or propel
objects resulting in serious injury. Always wear indirect
vented (chemical splash) safety goggles marked to
comply with ANSI Z87.1 when using or in vicinity of this
equipment. NEVER substitute safety glasses or dry-condition goggles
for indirect vented safety goggles.
1. Put on safety goggles.
2. Turn on water supply.
3. Push trigger lock (red button) (P) on spray gun and pull trigger
until water comes out in a steady stream. Release trigger to locked
position.
10
4. Place colored quick-connect spray tips (Q) in slots on holder that's
attached to nozzle extension (G).
5. Attach nozzle extension (G) to spray gun (F) Tighten by hand.
6. Choose desired spray tip (Q), pull back on the collar of nozzle
extension (G). Insert quick-connect spray tip and release collar. Tug
on spray tip to make sure it is securely in place.
7. Move throttle lever (R) to FAST (
NOTICE This unit is equipped with a ReadyStart® engine. A
ReadyStart® engine means there is no priming or choking required.
WARNING Starter cord kickback (rapid retraction) will pull hand
and arm toward engine faster than you can let go which
could cause broken bones, fractures, bruises, or sprains
resulting in serious injury. NEVER pull starter cord without
first relieving spray gun pressure. Pull starter cord slowly until
resistance is felt, then pull rapidly. Firmly grasp spray gun with both
hands when using high pressure spray to avoid injury when spray gun
D
kicks back.
8. When starting engine, position yourself as recommended and grasp
starter grip handle and pull slowly until you feel some resistance.
E
Then pull rapidly to start engine to avoid kickback. After each starting
attempt, where engine fails to run, always point gun in safe direction,
press red button and squeeze spray gun trigger to release high
pressure.
15
9. Return starter grip handle slowly. DO NOT let rope "snap back"
against starter.
NOTICE Always keep the throttle lever in the "Fast" (
G
operating the pressure washer.
10. Point gun toward surface to be cleaned. Push trigger lock (red
button) and pull trigger to begin spraying.
Stop pressure washer
1. Let engine idle for 2 minutes.
2. Move throttle lever (R) to SLOW (
position.
14
3. Turn off water supply.
4. Always point spray gun in safe direction, press red button, and
squeeze spray gun trigger to relieve retained high water pressure.
5. Disconnect garden hose from pump.
6. Disconnect high pressure hose from pump and gun for storage. For
long term storage instructions, see operator's manual.
7. Remove safety goggles.
Have Questions?
Do not return to store. We can help.
Call Customer Service Toll-Free 1-800-743-4115
or visit our website, www.brutepower.com
6
6
7
F
7
8
8
9
9
10
11
G
12
11
12
13
) position.
14
13
Q
14
15
) position when
) position, then STOP ( )
Exhaust Port
Pointed away from
dwelling openings
H
H
K
M
N
P
Q
F
G
G
R