Battery Charging; Cleaning The Battery And Cables - Allis-Chalmers YT9500 Serie Manual Del Usuario

Electronic Fuel Management System
The Electronic Fuel Management System monitors engine
temperature, engine speed, and battery voltage to adjust
the choke during engine starting and warm up. There are no
adjustments on the system. If starting or operation problems
occur, contact an authorized dealer.
NOTICE: Make sure to follow the steps below or the
Electronic Fuel Management System could be damaged.
»Ì»È ÉÊ·ÈÊ Ê¾» »Ä½¿Ä» ¿¼ ʾ» ¸·ÊÊ»ÈÏ ¹·¸Â»É ·È» ÂÅÅÉ»
ËÈÄ Ê¾» Á»Ï ÊŠʾ» ż¼ ÆÅÉ¿Ê¿ÅÄ ¸»¼ÅÈ» º¿É¹ÅÄÄ»¹Ê¿Ä½
removing and/or installing the battery.
»Ì»È ËÉ» · ¸·ÊÊ»ÈÏ ¹¾·È½»È ÊÅ ÉÊ·ÈÊ Ê¾» »Ä½¿Ä»
»Ì»È º¿É¹ÅÄÄ»¹Ê ʾ» ¸·ÊÊ»ÈÏ ¹·¸Â»É ;¿Â» ʾ» »Ä½¿Ä» ¿É
running.
¾»Ä ¹ÅÄÄ»¹Ê¿Ä½ ʾ» ¸·ÊÊ»ÈÏ ¹·¸Â»É ¼¿ÈÉÊ ¹ÅÄÄ»¹Ê ʾ»
positive (+) cable and then connect the negative (-) cable
to the battery.
¾»Ä ¹¾·È½¿Ä½ ʾ» ¸·ÊÊ»ÈÏ ÊËÈÄ Ê¾» ¿½Ä¿Ê¿ÅÄ ÉͿʹ¾ ÊŠʾ»
off position and disconnect the negative (-) battery cable
from the battery.
Å ÄÅÊ ÉÆÈ·Ï Í·Ê»È º¿È»¹ÊÂÏ ÅÄ Ê¾» »¹ÊÈÅÄ¿¹ ÅÄÊÈÅ Ä¿Ê

Battery Charging

WARNING
Keep open flames and sparks away from the
battery; the gasses coming from it are highly
explosive. Ventilate the battery well during
charging.
A dead battery or one too weak to start the engine may
be the result of a defect in the charging system or other
electrical component. If there is any doubt about the cause
of the problem, see your dealer. If you need to replace the
battery, follow the steps under Cleaning the Battery and
Cables.
To charge the battery, follow the instructions provided by
the battery charger manufacturer as well as all warnings
included in the safety rules sections of this book. Charge
the battery until fully charged. Do not charge at a rate higher
than 10 amps.
22

Cleaning the Battery and Cables

WARNING
When removing or installing battery cables,
disconnect the negative cable FIRST and reconnect
it LAST. If not done in this order, the positive terminal
can be shorted to the frame by a tool.
1. Disconnect the cables from the battery, negative cables
first (A, Figure 12) then the cover and positive cables (B).
2. Loosen the wingnut and washer (D).
3. Pivot the hold-down rod (C) up and away from battery.
Secure to steering tower.
4. Remove the battery (E).
5. Clean the battery compartment with a solution of baking
soda and water.
6. Clean the battery terminals and cable ends with a wire
brush and battery terminal cleaner until shiny.
7. Reinstall the battery (E) in the battery compartment.
Secure with the battery hold-down rod (C) and wingnut &
washer (D).
8. Re-attach the battery cables, positive cables and cover
first (B) then the negative cables (A).
9. Coat the cable ends and battery terminals with petroleum
jelly or non-conducting grease.
D
A
B
C
E
Figure 12