Publicidad
E
INSTRUCTION MANUAL
Main Unit Preparation
When using the unit for the first time or
after replacing battery, follow this procedure.
All Clear Operation
Press Main button and SET button simultaneously.
→All displays illuminate, and then "k" symbol flashes.
Scale Selection
Press Main button
and select "k (km)" or "m (mile)".
Press SET button to fix it
Wheel Circumference Setting
Increase the figure by Main button
(to increase rapidly, hold down the button).
Press SET button to fix it
Preparation Completed
How to Install
1 Bracket
2 Wire
3 Sensor
4 Magnet
5 Bracket
Rubber Pad
6 Nylon Ties
SPD
Current Speed
0.0(4.0) - 100 km/h ±1 km/h [0.0(3.0) - 60 mph ±1] (under 60 km/h)
The data is updated once a second.
When it reaches 60km/h (or 60mph), the decimals are omitted.
ODO
Total Distance (Odometer)
Continuously measured until battery wears down.
At 9999.9 km, it returns to zero and counting begins anew.
MX
Maximum Speed
Displays the highest recorded speed. When it reaches 60 km/h (or 60
mph), the decimals are omitted. With reset operation, it returns to zero.
DST
Trip Distance
The trip distance from start to current point is displayed. With reset op-
eration, it returns to zero.
Power Saving Function
When the main unit does not receive a signal, or a button has not been
pressed for about 70 minutes, the power supply is shut down and only
mode mark flashes . By pressing the Main button, or by receiving signal,
this function is released.
All manuals and user guides at all-guides.com
A. Data Display
B. Mode Symbol
C.Scale Symbol
D.Main Button
E. SET Button
F. Battery Case Cover
G.Contact
All Clear
Operation
SET(on back)
Button Operation
Press
simultaneously
In Wheel Circumference
Setting Display:
L
SET ( on back )
Measure the wheel circum-
ference by traveling your
bike on the ground for one
full wheel revolution. Or "Se-
lecting Values Cross Refer-
ence Table" tells you an ap-
proximate circumference
according to your tire size.
1
magnet
spoke
2
sensor's
marking
line
magnet's
center
clearance (2mm)
sensor
Align the magnet's center
and the sensor's marking
front fork
line. Make sure of 2mm
clearance between the
magnet and sensor. Tem-
porality attach the sensor
to the fork with the self-ad-
hesive patch.
0.0 - 9999.9 km [mile] ±0.1 km [mile]
0.0(4.0) - 100 km/h ±1 km/h [0.0(3.0) - 60 mph ±1]
0.00 - 999.99 km[mile] ±0.01 km[mile]
• Don't pay too much attention to your computer functions while riding. Keep your eyes
on the road and give due consideration to safe riding.
• Securely attach the magnet, sensor and bracket to your bicycle. Periodically check if
the screws and secure bands have loosened.
• Safely dispose of the old battery. Do not place it within children's reach. If swallowed
by mistake, consult a doctor immediately.
• Do not leave the main unit exposed to direct sunlight. Never disassemble the main unit.
• For cleaning, use neutral detergent on soft cloth, and wipe off with dry cloth. Do not
apply paint thinner, benzine or alcohol, to avoid damages on the surface.
• If there is mud, sand or the like clogged between the button and the body, the move-
ment of the button may be deteriorated. Softly wash away such objects with water.
In Ordinary Display
When you start/stop riding, the unit
automatically starts/stops measuring.
Just press
While measuring, the scale symbol "k" or "m" flashes.
SET(on back)
Hold down
Completes setting
→Return to measuring
Increases the figure
Rapidly increases the figure
3
Test
Slide the main unit onto the
bracket according to ''How to At-
tach Main Unit to Bracket" (be-
low). Spin the front wheel and
check if the scale symbol
flashes. (If not, adjust the relative
positions of the magnet and sen-
sor again.) After the test, remove
the main unit.
4
nylon tie
pull
Fix the sensor with the nylon ties.
Note: Fasten the ties securely.
Trouble Shooting
No display.
Has the battery in the main unit worn out?
Replace it with a new one.
Incorrect data appears.
Do "All Clear" operation.
Current speed does not appear. (When current speed does not appear, first short-circuit
the contact on the back with metal; if the speed display appears, the main unit is normal
and the problem must be in the bracket or the sensor.)
Is there anything on the contact of the main unit or of the bracket?
Wipe the contact clean.
Is the distance between the sensor and the magnet too far?
Are the marking line of the sensor and the center of magnet aligned?
Adjust the position of the sensor and magnet again.
Is the wire broken?
Replace it with a new one.
Current speed does not appear in wet condition.
Wipe the contacts with dry cloth. Contacts can also be treated with a water repellent
silicon jell from an automotive parts store or hardware store. Do not use industrial
water repellent; it may damage the bracket.
close
How to Replace Battery
When the display becomes dim, the battery is at the end of its
open
useful life. Replace it with a new lithium battery (CR2032) with the
(+) pole upward. After replacing battery, be sure to perform "All
Clear" operation and set the scale and wheel size again, as in the
"Main Unit Preparation".
Specifications
Applicable Wheel Circumference -- 112cm - 255cm (initial figure: 205 cm)
The length of the wire -------------- 70cm
Power Supply ------------------------ Lithium Battery (CR2032) x 1
Battery Life ---------------------------- Approx. 3 years (The life of the first factory-loaded battery may be
shorter than this period.)
Dimension/Weight ---------------------- 1-25/32" x 1-9/16" x 5/8" [45 x 40 x 15.5 mm ] / 0.85 oz. [24 g]
* The specifications and design are subject to change without notice.
In ODO display:
Wheel Size Setting
Changes the
display as in
the right figure
Resets data
(In MX or DST
display)
5
bracket
brake cable
wire
Secure the wire along the fork with
the nylon ties, and wind it round the
brake cable up to the handlebar.
Note: Allow enough wire length in
nylon ties
the area marked with
the illustration, to insure full
movement and unhindered
operation of the handlebar.
How to Attach Main Unit to Bracket
lever
Slide the main
u n i t o n t o t h e
slide
bracket from front un-
til it clicks into position.
To remove it, pull it off
forward while pushing
down the lever.
SPD
ODO
MX
DST
rubber pad
handlebar
in
Publicidad
