Operating Elements And Connections; Transmitter Siem-2T; Safety Notes - Monacor International JTS SIEM-2/5 Manual De Instrucciones

Ocultar thumbs Ver también para JTS SIEM-2/5:
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

All operating elements and connections de -
scribed can be found on the fold-out page 3.
1 Operating Elements
and Connections

1.1 Transmitter SIEM-2T

1 Combined XLR / 6.3 mm jacks MIC / LINE 1 and
2 (bal.), each to connect a microphone or an
audio signal source, e. g. mixer, preamplifier
2 Control INPUT VOL to set the input level, each
for the inputs MIC / LINE 1 and 2
3 Level indicator AF / PEAK, each for the inputs
MIC / LINE 1 and 2
LED shows green at and above a certain signal
level
LED shows orange when the level limit has
almost been reached
LED shows red when the level limit has been
reached
4 Channel display
5 Button SET to set the channel:
1. Keep the button pressed until the dot on the
right of the channel display (4) starts flashing.
2. Press the button repeatedly to select the
desired transmission channel (0 – 9, A, b, C,
d, E, F).
3. When the dot stops flashing, the setting has
been stored.
6 Power switch
To switch off, briefly keep the button pressed
until the channel display (4) is extinguished.
7 Transmitting antenna
8 Outputs LOOP OUT to route the inputs signals
from the jacks MIC / LINE 1 and 2 (1) to the
inputs of another audio unit (e. g. amplifier or
second transmitter)
9 Strain relief for the cable from the power supply
unit
To prevent accidental disconnection of the plug
from the jack (11), wrap the cable around the
hook from below.
10 Button TX BOOSTER for the transmission power
button disengaged = low transmission power
(10 mW)
button engaged = high transmission power
(50 mW)
11 Jack for power supply via the power supply unit
provided
8
1.2 Receiver SIEM-2 / R5
12 On-off switch with volume control for the ear-
phones
13 Button SET to set the channel (also see item 5)
14 Channel display
To save the batteries, the channel display only
lights up briefly after switching on. When you
press the button SET (13), it lights up again for
a few seconds.
15 Battery compartment cover
16 Receiving antenna
17 Control LINE / MIC GAIN to set the gain for the
input LINE / MIC (18)
18 Input (6.3 mm jack) to connect a microphone or
an audio unit
19 Belt clip
20 Jack
for the earphones
21 Power / Battery LED
When the LED shows red, replace the batteries.
22 Switch for the limiter

2 Safety Notes

The units (transmitter, receiver and power supply
unit) correspond to all relevant directives of the EU
and are therefore marked with
WARNING The power supply unit uses danger-
ous mains voltage. Leave servicing
to skilled personnel only. Inexpert
handling or modification of the unit
may result in electric shock.
G
The units are suitable for indoor use only. Protect
them against dripping water and splash water,
high air humidity and heat (admissible ambient
temperature range: 0 – 40 °C).
G
Do not place any vessel filled with liquid on the
units, e. g. a drinking glass.
G
Do not operate the transmitter and immediately
disconnect the power supply unit from the mains
socket
1. if one of the units is visibly damaged,
2. if a defect might have occurred after a unit was
dropped or suffered a similar accident,
3. if malfunctions occur.
In any case the units must be repaired by skilled
personnel.
G
For cleaning only use a dry, soft cloth; never use
water or chemicals.
.

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Jts siem-2/r5

Tabla de contenido