Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
Minimum Gauge for Cord Sets
Volts
Total Length of Cord in Feet
120V
0-25
(0-7,6m) (7,6-15,2m) (15,2-30,4m) (30,4-45,7m)
240V
0-50
(0-15,2m) (15,2-30,4m) (30,4-60,9m) (60,9-91,4m)
Ampere Rating
More
Not more
Than
Than
0
-
6
18
6
-
10
18
10
-
12
16
12
-
16
14
1
COMPONENTS
A. Power/Volume control
B. Antenna
C. Arrow buttons
D. Auxiliary port
E. LCD display
F. Memory button
2
G. Clock button
H. Bass button
I. Mode button
J. Outlets (2)
K. Battery compartment latch
L. Battery compartment door
M. 18V battery (not included)
N. Coin cell battery door
screw
O. Coin cell battery door
3
P. Coin cell battery
Q. Cord
N
O
P
26-50
51-100
101-150
51-100
101-200
201-300
American Wire Gage
16
16
14
16
14
12
16
14
12
12
Not Recommended
C
D
E
H
I
G
F
B
J
K
M
Q
L
4
OPERATING THE RADIO (FIG. 1, 2)
Your radio is equipped with memory capacity in order to store the time and your selected
memory channels. When the radio is in the OFF position, this memory capacity is
powered by one coin cell battery that is included with the radio.
TO INSTALL COIN CELL BATTERY
WARNING: Danger of explosion if battery is incorrectly replaced. When replacing
battery, replace it with the same or equivalent type CR2032. Observe correct polarity
(+ and –) when replacing batteries. Do not store or carry batteries so that metal objects
can contact exposed battery terminals.
WARNING: To reduce the risk of serious personal injury, turn tool off and
disconnect radio from power source before installing/changing battery.
1. Open the battery compartment by lifting the battery compartment latch (K).
2. Turn the screw (N) on the battery door (O) counterclockwise to remove.
3. Press down on the battery door latch and pull to open.
4. Install the coin cell battery (P) according to the diagram on the coin cell battery door.
5. Replace the battery door, insert the screw and tighten.
6. Securely close the battery compartment.
NOTE: To reset the LCD display (E), clock and pre-sets, remove the coin cell battery and
re-install. Follow this procedure if the screen seems to lock in place.
POWER/VOLUME ADJUSTMENT
1. To operate as a corded product, plug the radio into
an appropriate AC power outlet or generator.
2. To operate as a cordless product, open the battery
compartment as shown in figure 4 by lifting the battery
A
compartment latch (K). Insert a fully charged 18 volt
Porter Cable battery (M) into the battery cavity as
shown. Securely close the battery compartment door (L).
3. To turn the radio on, turn the power/volume dial (A)
clockwise until you hear a click.
4. Turn the power/volume dial (A) clockwise to increase
the volume. To decrease the volume, turn
counterclockwise.
MODE FUNCTION
To choose one of the mode functions (FM, AM, or AUX) push the mode button (I)
until the desired function is displayed on the LCD screen. For example, if the radio is on
FM, push the mode button two times to change to AUX.
TUNE OR SEEK FUNCTION
To Tune:
Push and hold down the right arrow button (C) to quickly move the tuner up the
frequency band. Release the button when the desired channel is reached. To quickly
move the tuner down the frequency band, push and hold down the left arrow button.
To Seek:
Press the right arrow button (C) once and release. The tuner frequency will increase to
seek the first radio station with acceptable clarity and stop at that station. The right arrow
button may be pressed again to continue seeking a radio station at higher frequencies.
The left arrow button may be pressed to seek radio stations at lower frequencies. The
seek function is available in AM and FM modes.
TO PROGRAM THE CLOCK
1. Turn power on (see Power/Volume Adjustment).
2. Push and hold clock button (G) until the LCD display (E) begins flashing, then release
clock button.
3. Press the appropriate arrow button (left arrow for hours; right arrow for minutes) to
adjust the time.
NOTE: If you do not press a arrow button within 5 seconds, the clock programming
feature will automatically return to the previous setting.
4. Once the time is set, push and hold the clock button until the time on the LCD display
stops flashing.
4
K
M
L
5
Publicidad
Tabla de contenido
