Publicidad
Idiomas disponibles
Idiomas disponibles
Before using your new Steren´s product, please read this instruction manual to prevent
I M P O R T A N T
The instructions of this manual are for reference about the product.
There may be differences due to updates.
Please check our web site (www.steren.com) to obtain the latest version of the
instruction manual.
C A U T I O N S
•
Do not try to open the device, may cause damages and warranty will be void.
•
Do not expose to extreme temperatures.
•
Do not use or store the equipment near wet places. May cause malfunction or shock hazard.
H I G H L I G H T S
This mixer has three channels and it is perfect for your parties or meetings. It includes microphone input, RCA
input channel (two) and USB input for power or audio transfer (using a PC).
Also, it has an independent two-band equalizer per channel and peak indicator.
The output is performed by a 3.5mm connector, allowing to record your audio files into a computer or to
plug into an amplifier o amplified speakers. The case is manufactured in low carbon steel.
•
One XLR microphone input
•
One two-channel audio input
•
One USB audio input (for computer)
•
One audio output
•
On / off switch
C O N T R O L S
1. USB port. It allows you to connect your console to a computer to use it as audio interface and for power
input.
2. Main switch. Turn on / off the unit.
3. Power LED. Illuminates when the console is turned on.
4. Mic/Line input. Insert an XLR cable or plug 6.3 mm monaural signal. To avoid damage, do not connect
any signal when the unit is turned on.
5. Line input. RCA jacks for stereo signal.
6. Input CD/Tape. In these ports you can connect an MP3 player, tape, CD, etc.
7. Output CD/Tape. Use this output to connect a recorder or amplifier.
8. Master output. Use to connect your console to an amplifier or active speakers.
9. Output for monitoring. Connect an amplifier or headphones for monitoring.
10. Gain control. Adjust the channel 1 gain.
11. Treble control. Controls the treble level.
12. Bass control. It allows to control the bass level.
13. PAN/BAL controls. These controls serve to boost the signal in some output channel (left or right).
any damage.
14. Peak LED. This LED turns on when there is signal on the channel. When the output signal is very high,
which can cause saturation or distortion, the LED will light red.
15. Channel volume. Here you can control the volume of each channel in the final mix.
16. Line/USB input selector. Press to select if you want to hear channels 2 and 3 line in input or USB audio.
17. CD / TAPE to main output signal selector. Press to send the signal CD / TAPE to the main output.
18. CD / TAPE to monitoring output signal selector. Press to send the signal CD / TAPE to monitoring
output.
19. Output volume control for monitoring. Use to increase / decrease the volume of the monitoring output.
20. Master output volume control. Turn to increase / decrease main volume.
21. L/R Clip indicators. They light up when the signal reaches a high level, which can cause distortion.
C O N N E C T I O N T O A C O M P U T E R
1. Connect the USB cable to the MIX-150 and to a computer.
2. Turn the MIX-150 on.
3. Wait for the necessary drivers are installed.
4. Select "USB Audio CODEC" as the preset audio input and output in the system options.
5. Open the recording program of your choice and make sure that "USB Audio CODEC" is selected as audio
input and output.
6. Make connections from microphones and inputs as needed.
7. Start recording.
8. Once you are finished, turn off the MIX-150 and disconnect all cables.
S P E C I F I C A T I O N S
Input: 5 V
500 mA
Microphone input: 20 mv non balanced
USB input: 16 Bits, 44.1 kHz
Line input: 1 V, non balanced
Headphone output: 300 mW @1%THD
THD: < 0.01% S/N vs max.output
Frequency response: 20 Hz – 22 kHz
SNR: >70 dB
Power converter
Input: 100-240 V~ 50/60 Hz 300 mA
Output: 5 V
550 mA
Product design and specifications are subject to change without notice.
Product: USB portable mixer
Part number: MIX-150
Brand: Steren
This Steren product is warranted under normal usage against defects in workmanship and materials to the original purchaser for one year from
the date of purchase.
1. This warranty card with all the required information, invoice or purchase ticket, product box or package, and product, must be presented when
warranty service is required.
2. If the product is in the warranty time, the company will repair it free of charge.
3. The repairing time will not exceed 30 natural days, from the day the claim was received.
4. Steren sell parts, components, consumables and accessories to customer, as well as warranty service, at any of the addresses mentioned later.
THIS WARRANTY IS VOID IN THE NEXT CASES:
If the product has been damaged by an accident, acts of God, mishandling, leaky batteries, failure to follow enclosed instructions, improper repair by
unauthorized personnel, improper safe keeping, among others.
a) The consumer can also claim the warranty service in the purchase establishment.
b) If you lose the warranty card, we can reissue it, if you show the invoice or purchase ticket.
RETAILER INFORMATION
Name of the retailer ____________________________________
Address _____________________________________________
Product ______________________________________________
Brand _______________________________________________
Serial number _________________________________________
Date of delivery _______________________________________
In case your product fails or have questions, please contact your nearest dealer. If you are in Mexico, please call to our Call Center.
+10
WARRANTY
CONDITIONS
01 800 500 9000
Publicidad
