koban KOBAMATIC DIGI-03 Manual Del Usuario

Code: 0767633 - Reference: KOBAMATIC DIGI-03
Pls first reset the unit, following point 5.4 to see the details.
I、To set the current day and time
1.1.Hold "set" for three seconds, the week will flash, then push "←" or "→" can adjust the week, if push the key long time can
adjust the week fast.
1.2. Press the "set" key again, then Hour will be flash, then push "←" or "→" can adjust the hour, if push the key long time can
adjust the hour fast
1.3 Press the "set" key again, then MIN will be flash, then push "←" or "→" can adjust the minutes, if push the key long time
can adjust the minute fast
1.4 Press the "set"again finish to set the current day and time, and the LCD will display the current time and unit will begin to
work.
II、Set the timer program
2.1 During the LCD display the current time, press '→'key, then it were go into the timer setting mode, and 1 ON will flash
2.2 Press the "SET" key then confirm enter into 1ON set, at the same time the week will be filash, then press '←' or ' →' can
adjust the week or week group, the week group is as follows: （ Mon、Tue、Wed、Thu、Fir、Sat、Sun） （Mon） （Tue）
（Wed） （Thu） （Fir） （Sat） ( Sun)（Mon、Tue、Wed、Thu、Fir） （Sat、Sun） （Mon、Tue、Wed、Thu、
Fir、Sat） （Mon、Wed、Fir） （Tue、Thu、Sat） （Mon、Tue、Wed） （Thu、Fir、Sat） （Mon、Tue、Wed、
Thu、Fir、Sat、Sun） 。If push the "SET"key long time can adjust fast
2.3 Then press"SET"key, the HOUR will be flash then press'←'or'→'can adjust hour, keep long time can adjust it fast
2.4 Then press"SET"key, the MIN will be flash then press'←'or'→'can adjust minutes, keep long time can adjust it fast
2.5 Then press "SET" key to confirm the set just now. at the same time the 1ON will flash. Then press "MANUAL" key cancel
the 1ON set, at any situation this action can use, if on WEEK, HOUR,MIN flash situation and press "MANUAL "key can
cancel the 1ON set. If press "SET" can reset again ( then the all data will be change in zero), if now press "MANUAL " key
again can come back the 1ON set (at the same time the data will keep)
2.6 On 1ON flash situation, press "SET"key enter into 1OFF set and 1OFF will flash, then press '←'enter into 2OFF set the
same as 1ON set
2.7 Repeat the above action can set 2OFF, 3ON......
2.8 On any setting situation press "MANUAL " can exit the set and LCD display the current time.
2.9 Not: timer program setting should on AUTO mode, and also have no other priority program work can use
III. Timer ON/OFF mode
3.1 When on display the current time, press " MANUAL" key, the LCD will point out on OFF-AUTO OFF- ON- AUTO
ON-OFF circle
3.2 Display ON the timer will on and display OFF the timer will off
3.3 Display AUTO will according with the set timer program work
IIII: Countdown timer function
4.1 When on LCD display the current time and then press ' ←' enter into countdown time set and on the LCD top right side will
show CTD
4.2。 Press "SET"enter into the set mode and HOUR will flash, then press '←' or ' →' can adjust the hour, press long time can
adjust fast
4.3 Press "SET" again the MIN will flash, then press '←'or'→'can adjust the minutes, press long time can adjust fast
4.4 Press "SET" again the SEC will flash, then press '←'or'→'can adjust the seconds, press long time can adjust fast
4.5 Press "SET" to confrm the setting, if now push "MANUAL" key can cancel the countdown time set just now and if press
"MANUAL" again can comeback the orginal set.
4.6 On any condition of countdown time setting, means when on HOUR, MIN or SEC flash can press the "CTD" key begin the
countdown time
4.7 On countdown time working time press "CTD" key will pause the countdown time and will also display the left time of the
countdown time, and press the "CTD" again to continue the countdown time.
4.8 On countdwon time working time, press " TIME " key can check the current time, if push "CTD" key or 3 sec. later will
back to the countdown timer display
4.9 When on countdown time pause time, press"TIME" key exit the countdown time and back to the current time display.
4.10 After countdown time finish will back to the current time display.