Crown CT44088-R Manual Original página 23

Mounting / dismounting on a tripod (see fig. 4)
You can install the mini tripod 13 on a tri-
•
pod 21 with a mounting thread 5/8"-11UNC (see
fig. 4). Attention: tripod 21 is not included in
delivery set.
• Install the appliance (with installed mini tri-
pod 13) on the tripod 21 as shown in fig. 4.
• Disassemble in the reverse sequence�
Magnet holder (see fig. 5-7)
• Install the appliance on the magnet holder 17
using the mounting screw 23 as shown in fig. 5.
You can rotate the appliance mounted on the
•
magnet holder 17 (see fig. 6).
• Release mounting screw 23 (see fig. 6.1).
• Rotate the appliance (see fig. 6.2).
Tighten mounting screw 23�
•
You can install the magnet holder 17 on fer-
•
romagnetic metal surfaces (elements of metal
structures, metal doors, frame structures for fixing
drywall, etc�) using the magnets 24 (see fig. 7.1).
In this case, the appliance shall be installed in the
position shown in figure 7.2. Note: if you flip the
appliance, the self-leveling system of the laser
head will be misguided.
• You can suspend the magnet holder 17 as
shown in figure 7.3.
Battery charging
Initial operating
The appliance is delivered with partial bat-
tery charge. Fully charge the battery before
the first use of the appliance.
If the all laser beam power indica-
tors 10 flashes when the appliance
is switched on, it means that the
battery discharged and needs to be
charged.
Charging (see fig. 8)
• Open the protective cover 12�
• Connect the plug of USB cable 16 to socket 25
(see fig. 8)� Connect the other end of USB cable 16
to suitable power unit 26 or USB socket�
During charging the indicators 10 will light
•
up one-by-one� When charging is complete, all
indicators 10 will light up�
• When charging is complete, unplug USB
cable 16 from socket 25 and disconnect USB
cable 16 from power unit 26 or USB socket�
During charging the appliance and
power unit 26 may become hot - it is
no problem.
Switching on / off
When self-levelling is on
Switching on:
Set lock 6 to position as shown in fig. 9.1. This will
unlock the suspension gear of the laser head and
turn power of all laser beams� Also indicators 2
and 10 lighting on� If the appliance is positioned
on the inclined surface with an angle of more
than ±4°, an indicator 2 will glow red and laser
beams will blinking� You can switch on and off the
laser beams pressing on / off switches 1, 9 or 11�
Switching off:
Set lock 6 to position as shown in fig. 9.2. This will
lock the suspension gear of the laser head, turn off
power of all lasers� Indicators 2 and 10 goes out�
When self-levelling is off
Switching on:
Set lock 6 to position as shown in fig. 9.2, then
press and hold the function switch 3 for a long
time� Indicator 2 will glow red and laser beams
will blinking every 5 seconds� Also indicators 10
lighting on� Laser power is now on, but the sus-
pension gear of the laser head is locked� You can
switch on and off the laser beams pressing on / off
switches 1, 9 or 11� When working in this mode, it
is possible to mark inclined lines�
Switching off:
Press and hold the function switch 3 for a long
time� Indicators 2 and 10 goes out, also power of
all lasers will be turn off�
Design features
Powering the appliance from the mains (see
fig. 8)
The appliance can powered from the mains� Open
the protective cover 12 and connect the plug of
USB cable 16 to socket 25 (USB type C)� Connect
the other end of USB cable 16 to suitable power
unit 26 or USB socket�
Laser head self-levelling system
Laser head self-levelling system makes laser
measurement possible, if the body of appliance
not in vertical position (inclination angle not ex-
ceeding ±4°)�
English
23