Stanley FatMax LIONHAL Manual De Instruccion página 4

OPERATING INSTRUCTIONS
Operating the spotlight
1. Disconnect from charger.
2. The On/Off trigger is located in the front of the handle of the spotlight.
3. To turn the spotlight on, squeeze the trigger.
4. To turn off the spotlight, release the trigger.
Note:
The On/Off trigger can be locked in the on position using the trigger lock bar on the side of the unit.
The battery/charge status LED indicator will light in one of three colors (as described in the "Reading the Battery/Charge Status LED Indicator" section) to
indicate the battery status.
Locking the spotlight
To lock the spotlight in the on position, depress the On/Off Trigger, then press the trigger lock bar. The spotlight will stay on until
the trigger unlock bar is pressed and the On/Off Trigger is released.
If the On/Off Trigger is released when the trigger lock bar is pressed, the spotlight will be locked in the off position. To turn the
spotlight on again, press the trigger unlock bar before pressing the On/Off Trigger.
Using the light mode select button
The spotlight offers two brightness modes.
When the spotlight is firstly turned on, the light is operating at maximum brightness. To operate the spotlight at medium
brightness, press the Light Mode Select Button on the back of unit once. Press it again to switch back to maximum brightness.
Operating the unit corded
Plug the barrel tip of the supplied 12 volt DC adapter into the 12 volt DC power and charging port at the back of the unit. Insert the
plug end into the accessory outlet of your vehicle or other 12 volt DC power source. Operate the unit as outlined in the previous section.
IMPORTANT: The spotlight will operate while the 120 Volt AC Adapter is attached, but will continue to draw power from the unit' s
Lithium-Ion battery and will not continue charging while the spotlight operates. Manufacturer recommends only operating the
unit in corded mode using the 12 Volt DC Adapter.
Using the Swing-up Stand
Snap the Swing-up Stand up, invert the unit and set it upon a flat, stable surface for hands-free operation.
Using the carry lanyard (optional accessory)
The carry lanyard may be used to carry the unit or to hang it for storage. Always adjust the slide on the cords to keep the lanyard
secure around any supporting object.
CAUTION: TO REDUCE THE RISK OF PRODUCT DAMAGE:
• When light is hung by the carry lanyard, do not shake the spotlight or object that it is hanging from. Do not hang the spotlight
from any electrical wires or anything that it is not secure.
• Only use the carry lanyard for hanging this spotlight. The carry lanyard is not intended to support additional weight. Do not attach
or hang anything additional to the spotlight or risk of breakage may occur.
CARE AND MAINTENANCE
All batteries lose energy from self-discharge over time and more rapidly at higher temperatures. When the unit is not in use, we
recommend that the battery is charged at least every 3 to 6 months.
Never submerge the unit in water. If the unit gets dirty, gently clean the outer surfaces of the spotlight unit with a soft cloth moistened with
a mild solution of water and detergent.
Except for the H3, 40 watt bulb, there are no user-replaceable parts. Periodically inspect the condition of adapters, connectors and
wires. Contact manufacturer to replace any components that have become worn or broken.
Battery replacement/disposal
BATTERY REPLACEMENT
The battery should last the service life of the unit. Service life is dependent on a number of factors including but not limited to
the number of recharge cycles, and proper care and maintenance of the battery by the end user. Contact manufacturer for any
information you may need.
SAFE BATTERY DISPOSAL
Contains a lithium-ion battery, which must be disposed of properly. Recycling is required. Failure to comply with
local, state and federal regulations can result in fines, or imprisonment.
Please recycle.
WARNINGS:
• Do not dispose of the battery in fire as this may result in an explosion.
• Before disposing of the battery, protect exposed terminals with heavy-duty electrical tape to prevent shorting (shorting can result
in injury or fire).
LIONHAL_LIONHALS_ManualENSP_073015.indd 6-7
6
• Do not expose battery to fire or intense heat as it may explode.
Spotlight Bulb Replacement
To replace the bulb, you will need a small Phillips screwdriver and a 11 volt, H3 40 watt replacement bulb. During installation, avoid
touching the glass part of the bulb. Bulb life may be shortened by installing a bulb with dirt or fingerprints on it. The bulb can be
wiped clean with a cloth moistened with alcohol.
RUBBER BEZEL
PHILLIPS
Use a screwdriver to gently
SCREW
pry the Rubber Bezel off.
PHILLIPS SCREW
RUBBER
"O" RING
RETAINING
RING
HALOGEN BULB ASSEMBLY
HAIRPIN
RETAINING
WIRE
LIGHT REFLECTOR
1. Disconnect the unit from any charging adapters.
2. Push the rubber bezel forward toward the front of the spotlight to reveal two small Phillips screws in the retaining ring.
3. Using the screwdriver, remove (counterclockwise) the two screws. Set them aside.
4. Lift off the retaining ring, glass lens and rubber "O" ring and set them aside.
5. Carefully remove the reflector and bulb assembly.
6. Disconnect the bulb wire from the red power wire.
7. Unsnap the hairpin retaining wires from the reflector' s flange.
8. Using the screwdriver, loosen the retaining screw to remove the bulb from the reflector (no need to completely remove this
screw).
9. Lift out the bulb and detach wire.
10. Insert the replacement bulb into the reflector' s flange.
11. Put back and secure the hairpin retaining wires.
12. Connect the bulb power wire to the red power wire.
13. Tighten the retaining screw on the flange.
14. Place the reflector in position in the body of the spotlight.
15. Replace the glass lens rubber "O" ring in the groove around the perimeter of the reflector.
16. Replace retaining ring so the screw holes are aligned.
17. Secure retaining ring with two screws.
18. Replace rubber bezel.
19. Operate switch to ensure proper operation of spotlight.
WARNING: To reduce the risk of electric shock, replace bulb with 11 volt, H3 40 watt only.
12 volt DC Adapter plug fuse replacement
The fuse in the plug end of the 12 Volt DC Adapter protects the adapter' s charging circuit. If the 120 Volt AC Adapter operates, but the DC
charging adapter does not, then this fuse may be opened (blown).
LIGHT
REFLECTOR
ON/OFF
GLASS TRIGGER
LENS
HALOGEN BULB
ASSEMBLY
Only replace the bulb in an
integrated assembly of lamp
holder, wire and tab.
RETAINING
SCREW
7
7/30/2015 10:46:10 AM