Warnings - Assembly Text Instructions - Maintenance - Extremis Tiki Manual De Instrucciones

Warnings – Assembly text instructions – Maintenance
English
WARNINGS
General
• Do not use any sharp tools to open the
packaging.
• We strongly advise against using power tools.
• Tripping hazard, mind your step.
• Not grafitti proof.
• Do not leave children unattended whilst playing
on the chair.
• To avoid danger of suffocation, keep plastic bags
away from babies and children.
• Colours can differ over years and from batch to
batch.
Product
• Do not lean forewards, always stay on 4 feet.
• Stackable up to 4 pieces.
• Max. 1 person or 120 kg per seat.
Wood
• When delivered, the wood is oiled.
• Wood is a natural material and its look is different
for every slat, plank and tree.
• Cleaning regularly with mild detergent. Never use
a high pressure cleaner as this will roughen the
wood's smooth surface and irreparably damage
the wood's fibress.
Powder-coating
• White powder-coating requires more
maintenance.
• Do not use abrasive scouring powders or
scourers as they will scratch the surface.
• Colour can fade to some extent when exposed to
UV.
• Flame retarding - NEN-EN13501-1 A2-sl -
Satisfying the same criteria as Class B for the
SBI-test according to EN13823. In addition,
under conditions of a fully developed fire these
products will nog significantly contribute to the
fire load and fire growth.
• Dark colors can get very hot in sunny weather.
Felt
• Stains should be removed immediately with a
clean, soft cloth, particularly in case of dark-
coloured liquids such as wine, ink, coffee coke,
oild and bird droppings. If left to dry, these
12
liquids may cause permanent damage!
• Do not bleach to clean.
ASSEMBLY INSTRUCTIONS
High stool - p6
1. a. With powder-coated seat Lay the seat upside
down on the floor or a table, using the packaging
as protection. Attach the frame to the seat with 4
M6 wave washers and 4 M6 self-locking nuts as
shown in the drawing. Caution: Tighten the bolts
properly but not too tight! Max. 8 Nm or 4 kg or
8,8 lb.
b. With wooden seat Lay the seat upside down
on the floor or a table, using the packaging as
protection. Attach the seat to the chassis with 4
M6x10 bolts and 4 M6 wave washers as shown in
the drawing.
Medium stool - p7
1. a. With powder-coated seat Lay the seat upside
down on the floor or a table, using the packaging
as protection. Attach the frame to the seat with 4
M6 wave washers and 4 M6 self-locking nuts as
shown in the drawing. Caution: Tighten the bolts
properly but not too tight! Max. 8 Nm or 4 kg or
8,8 lb.
b. With oak seat Lay the seat upside down on
the floor or a table, using the packaging as
protection. Attach the seat to the chassis with 4
M6x10 bolts and 4 M6 wave washers as shown in
the drawing.
Low stool - p8
1. a. With powder-coated seat Lay the seat upside
down on the floor or a table, using the packaging
as protection. Attach the frame to the seat with 4
M6 wave washers and 4 M6 self-locking nuts as
shown in the drawing. Caution: Tighten the bolts
properly but not too tight! Max. 8 Nm or 4 kg or
8,8 lb.
b. With oak seat Lay the seat upside down on
the floor or a table, using the packaging as
protection.
Attach the seat to the chassis with 4 M6x10 bolts
and 4 M6 wave washers as shown in the drawing.
Backrest - p9
1. Lay the seat upside down on the floor or a table,
using the packaging as protection. Place the
frame on the seat as shown in the drawing.