Safety Information - Cub Cadet CS59L Manual Del Operador

• When starting the unit, always allow the motor to achieve full speed before beginning a cut. Fully squeeze
the switch trigger and maintain a steady cutting speed. Slower speeds increase the chance of kickback.
Keep the saw housing pressed firmly against the wood.
• Watch for shifting logs, branches, or other objects that might pinch, or fall onto, the chain while cutting.
• If using wedges, only use wedges made of plastic or wood. Do not use metal to hold a cut open.
• Follow the manufacturer's sharpening and maintenance instructions for the saw chain.
• Use only replacement bars and chains specified by the manufacturer or the equivalent.
• Use devices, such as low-kickback chains, guide bar nose guards, chain brakes and special guide bars,
which reduce the risks associated with kickback. There are no other replacement components for
achieving kickback protection in accordance with CSA Z62.3.
• Low-kickback saw chain is chain that has met the kickback performance requirements of ANSI B175.1-1991
and is in accordance with CSA Z62.3. Do not use other replacement chain unless it has met these
requirements for the specific model. As saw chains are sharpened, some of the low kickback qualities are
lost and extra caution should be used.
OTHER SAFETY PRECAUTIONS
• DO NOT operate the unit with one hand! Serious injury to the operator, helpers or bystanders may result
from one-handed operation. This unit is intended for two-handed use.
• DO NOT handle the unit with wet hands.
• DO NOT operate a chain saw in a tree or on a ladder unless specifically trained to do so.
• DO NOT expose the unit to rain. Do not use the unit in damp or wet locations or conditions.
• DO NOT operate the unit on wet surfaces.
• DO NOT use the unit in the presence of flammable liquids or gases.
• DO NOT operate a unit that is damaged, improperly adjusted or not completely and securely assembled.
Be sure that the unit stops when the trigger is released. Do not use the unit if the switch does not turn the
unit on and off properly or if the switch lock does not work.
• DO NOT attempt operations beyond the operator's capacity or experience.
• DO NOT cut near electrical cables or power lines.
• DO NOT force the chain saw, especially near the end of a cut. It will do a better, safer job when used at
the intended rate.
• To reduce the risk of electric shock, avoid body contact with grounded conductors, such as metal pipes
or wire fences.
• Keep all body parts away from the saw chain when the motor is operating. Before starting the saw, make
sure the saw chain is not contacting anything.
• Always stop the motor when operation is delayed, before setting down the unit or when walking from one
location to another. Make sure the chain comes to a complete stop.
• To avoid accidental starting, never carry the unit with fingers on the switch trigger.
• Always carry the chain saw by the front handle with the battery removed, finger off the switch trigger and the
guide bar and saw chain sheathed in the scabbard and positioned to the rear.
• Always make sure the switch lock is in the locked or OFF position before installing or removing the battery.
• Cut wood only. Do not use the chain saw for purposes for which it was not intended.
• When cutting a limb that is under tension, be alert for spring back, which may cause the operator to
be struck when the tension of the wood fibers is released.
• Use extreme caution when cutting small-sized brush and saplings, as slender material may catch the
saw chain and be whipped toward the operator or pull the operator off balance.
• This saw is classified by ETL as a Class 2C saw. It is intended for infrequent use by homeowners,
cottagers and campers, and for general applications such as clearing, pruning, cutting firewood, etc.
It is not intended for prolonged use. If the intended use involves prolonged periods of operation, this
may cause circulatory problems in the user's hands due to vibration. It may be appropriate to use a
saw having an anti-vibration feature.
MAINTENANCE AND STORAGE SAFETY
• DO NOT perform maintenance procedures other than those described in this manual. Do not
attempt to repair; there are no user serviceable parts inside.
• Follow all maintenance instructions in this manual.
• Before inspecting, servicing, cleaning, storing, transporting or replacing any parts on the unit:
1. Make sure all moving parts have stopped.
2. Allow the unit to cool.
3. Make sure the switch lock is in the locked or OFF position.
4. Remove the battery.
• Never remove, modify or make inoperative any safety device furnished with the unit.
• For safer, more effective performance, make sure the bar and chain are properly cleaned, lubricated,
tightened and sharpened. Check the bar and chain at frequent intervals for proper adjustment.
• Frequently inspect the unit for damage. Before further use, any damaged part should be carefully checked
to determine that it will operate properly and perform its intended function. Check for alignment of moving
parts, binding of moving parts, breakage of parts and any other conditions that may affect its operation.
Damaged parts should be properly repaired or replaced.
• Use only original manufacturer replacement parts and accessories, which are designed specifically to
enhance the performance and maximize the safe operation of the product. Failure to do so may cause
poor performance and possible injury. Use only the chain and guide bar supplied with this product.
• Remove the battery from the unit when not in use.
• Be sure to secure the unit while transporting.
• Always use the scabbard on the bar and chain during transportation and storage.
• When not in use, store the unit in a locked-up and dry, or high and dry, place to prevent unauthorized use
or damage. Keep out of the reach of children.
• Keep the handles dry, clean and free from debris, oil and grease. Clean the unit after each use. Never
douse or squirt the unit with water or any other liquid. Do not use solvents or strong detergents.
• If dropped in water, do not use the unit.
2

SAFETY INFORMATION

• SAFETY AND INTERNATIONAL SYMBOLS •
This operator's manual describes safety and international symbols and pictographs that
may appear on this product. Read the operator's manual for complete safety, assembly,
operating, maintenance and repair information.
SYMBOL MEANING
• SAFETY ALERT SYMBOL
Indicates danger, warning or caution. May be used in conjunction with other
symbols or pictographs.
• READ OPERATOR'S MANUAL
WARNING:
and safety instructions. Failure to do so can result in serious injury to the operator
and/or bystanders.
• WEAR HEAD, EYE AND HEARING PROTECTION
WARNING:
injury and hearing loss. Wear eye protection meeting ANSI Z87.1-1989
standards and ear protection when operating this unit. Wear head protection
when operating this unit; falling objects can cause severe head injury. Use a
full face shield when needed.
• KEEP BYSTANDERS AWAY
WARNING:
least 100 feet (30 m) from the operating area. If anyone enters the work area,
stop the unit!
• WEAR SAFETY GLOVES
Wear non-slip, heavy-duty protective gloves when handling the unit.
• WEAR SAFETY FOOTWEAR
Wear non-slip safety footwear when using this equipment.
• USE BOTH HANDS
Always use both hands while operating the chain saw. Never use only one
hand to operate the unit.
• KICKBACK WARNING
Contact of the guide bar tip with any object should be avoided. Tip contact
may cause the guide bar to move suddenly upward and backward, which
may cause serious injury.
• DO NOT USE IN THE RAIN
WARNING:
unit in the rain or in damp or wet conditions. Moisture is a shock hazard.
SAVE THESE INSTRUCTIONS
Read the operator's manual(s) and follow all warnings
Thrown objects and loud noise can cause severe eye
Keep all bystanders, especially children and pets, at
Avoid dangerous environments. Never operate your