Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
HYBL-03
Hyundai Kia amplified
Blue Link interface 2010-up
• Retains factory Blue link (if equipped)
• Provides navigation outputs
• USB updatable
• Retains fade and balance
• Used with the SPIDIF systems
• Retains factory backup camera
• Retains factory 3.5 mm jack
• High level speaker input
• Prewired ASWC-1 harness included (ASWC-1 sold separately)
applIcatIons
KIa
Sorento (with NAV)
2011-2013
Interface components
• HYBL-03 Interface • 16-pin harness with stripped leads
•18-pin to 16-, 20- & 24-pin connector
tools requIred
• Cutting tool • Tape • Crimping tool
• Connectors (i.e. butt-connectors, bell caps, etc.)
METRA. The World's best kits.
Installation Instructions for HYBL-03
features
HYundaI
Tucson (with NAV)
2010-2012
™
1-800-221-0932
Caution: Metra recommends disconnecting the negative battery terminal before beginning
any installation. All accessories, switches, and especially air bag indicator lights must be
plugged in before reconnecting the battery or cycling the ignition.
*Note: Refer also to the instructions included with the aftermarket radio.
connectIons on tHe Interface
from the 16-pin harness with stripped leads:
• Connect the red wires to the ignition wire of the aftermarket radio.
• Connect the White wire to the left front positive speaker output of the
aftermarket radio.
• Connect the White/Black wire to the left front negative speaker output of the
aftermarket radio.
• Connect the Gray wire to the right front positive speaker output of the
aftermarket radio.
• Connect the Gray/Black wire to the right front negative speaker output of the
aftermarket radio.
• Connect the Green wire to the radio's left rear positive speaker output.
• Connect the Green/Black wire to the radio's left rear negative speaker output.
• Connect the purple wire to the radio's right rear positive speaker output.
• Connect the purple/Black wire to the radio's right rear negative speaker output.
• Connect the Blue/White wire to the radio's amp turn on wire.
• Connect the Brown wire to the mute wire of the aftermarket radio.
If the aftermarket radio does not have a Mute wire, tape up the Brown wire.
• Connect the light Green wire to the parking brake wire of the aftermarket
navigation radio.
• The Green/purple wire will not be used in this application.
• The Blue/pink wire will not be used in this application.
• The orange/White wire will not be used in this application.
metraonline.com
(continued on next page)
© COPYRIGHT 2004-2011 METRA ELECTRONICS CORPORATION
Publicidad
Manuales relacionados para Metra Electronics HYBL-03
Resumen de contenidos para Metra Electronics HYBL-03
- Página 1 • Connect the Blue/White wire to the radio’s amp turn on wire. • Connect the Brown wire to the mute wire of the aftermarket radio. • HYBL-03 Interface • 16-pin harness with stripped leads If the aftermarket radio does not have a Mute wire, tape up the Brown wire.
- Página 2 Interface (continued) from the 16-pin harness: testing and adjusting the HYBl-03 • Connect the Yellow wire to the 12-volt constant/battery wire of the aftermarket radio 1. Turn the aftermarket radio on. • Connect the Black wire to the ground wire of the aftermarket radio 2.
- Página 3 • Conecte el cable azul/blanco con el cable de encendido del amplificador • Interfase HYBL-03 •Arnés de 16 pins con conectores pelados • Conecte el cable café con el cable de silencio del radio de mercado secundario. Si el radio de •...
- Página 4 ASWC-1 para la programación instalación del HYBl-03 1. Cuando termine todas las conexiones, conecte los arneses de 16 y 18 pins al HYBL-03. 2. Conecte el arnés de 24 y 18 pins en el arnés lateral del vehículo y conecte el arnés del radio de mercado secundario en el radio de mercado secundario.