Tool Specifications; Fastener Specifications - Craftsman CMPBN18SB Manual De Instrucciones

English
• Avoid prolonged contact with dust from power
sanding, sawing, grinding, drilling, and other
construction activities. Wear protective clothing and
wash exposed areas with soap and water. Allowing
dust to get into your mouth, eyes, or lay on the skin may
promote absorption of harmful chemicals.

WARNING: Use of this tool can generate and/
or disperse dust, which may cause serious and
permanent respiratory or other injury. Always use
NIOSH/OSHA approved respiratory protection
appropriate for the dust exposure. Direct particles
away from face and body.

WARNING: Always wear proper personal hearing
protection that conforms to ANSI S12.6 (S3.19)
during use. Under some conditions and duration
of use, noise from this product may contribute to
hearing loss.

CAUTION: When not in use, place tool on its
side on a stable surface where it will not cause
a tripping or falling hazard. Some tools will stand
upright but may be easily knocked over.
• Air vents often cover moving parts and should be
avoided. Loose clothes, jewelry or long hair can be
caught in moving parts.
The label on your tool may include the following symbols. The
symbols and their definitions are as follows:
V ......................... volts
Hz ....................... hertz
min ..................... minutes
or DC ...... direct current
...................... Class I Construction
(grounded)
.../min .............. per minute
BPM .................... beats per minute
IPM ..................... impacts per minute
RPM .................... revolutions per
minute
sfpm ................... surface feet per
minute
SPM .................... strokes per minute
OPM .................... oscillations per
minute
A ......................... amperes
W ........................ watts
or AC ........... alternating current
SAVE THESE INSTRUCTIONS FOR
FUTURE USE
COMPONENTS (FIG. A)
Intended Use
Your nailer is designed for professional
fastening applications.
4
or AC/DC .... alternating or
direct current
...................... Class II
Construction
(double insulated)
n o ....................... no load speed
n ......................... rated speed
...................... earthing terminal
..................... safety alert symbol
..................... visible radiation
..................... avoid staring at
light
..................... wear respiratory
protection
..................... wear eye
protection
..................... wear hearing
protection
..................... read all
documentation
IPXX .................... IP symbol
DO nOT use under wet conditions or in presence of
flammable liquids or gases.
Your nailer is a professional power tool.
DO nOT let children come into contact with the tool.
Supervision is required when inexperienced operators use
this tool.

TOOL SPECIFICATIONS

Model CMPBn18sB
Length 9.25" (234.95 mm)
Height 9.5" (241.3 mm)
Width 2" (50.8 mm)
Weight 2.69 lbs (1.22 kg)

FASTENER SPECIFICATIONS

Model CMPBn18sB
Fixations Brad nail
Gauge 18
Fastener 5/8"– 2"
Range (15.87 mm - 50.8 mm)
Tool Air Fitting
This tool uses a free flow connecting plug 1/4" N.P.T. The
inside diameter should be .200" (5 mm) or larger. The fitting
must be capable of discharging tool air pressure when
disconnected from the air supply.
Operating Pressure
60 to 100 p.s.i.g. (4.92 to 6.9 kg/cm²). Select the
operating pressure within this range for best fastener
performance. DO NOT EXCEED THIS RECOMMENDED
OPERATING PRESSURE.
Adjustments and Usage Prep
Air Supply and Connections

WARNING: Do not use oxygen, combustible
gases, or bottled gases as a power source for this
tool as tool may explode, possibly causing injury.
Fittings
Install a male fitting on the tool which is free flowing
and which will release air pressure from the tool when
disconnected from the supply source.
hoses (Fig. A)
Air hoses should have a minimum of 150 p.s.i.g.
(10.6 kg/ cm²) working pressure rating or 150% of the
maximum pressure that could be produced in the air
system. The supply hose should contain a fitting that will
provide "quick disconnecting" from the 1/4" male fitting
on the tool.
supply source
Use only clean regulated compressed air as a power source
for this tool. NEVER USE OXYGEN, COMBUSTIBLE GASES, OR
CMPFn16sB
11.25" (285.75 mm)
11.5" (292.1 mm)
3" (76.2 mm)
4.03 lbs (1.82 kg)
CMPFn16sB
Brad nail
16
1"– 2.5" (25.4 mm - 63.5 mm)
3