Cooper Lighting RL56 Manual Del Usuario

ENGLISH
IL502448ML
8 7
RL56 Smart Bluetooth Speaker Downlight Instructions
PACKAGING CONTENTS
B. Socket Adapter (E26)
For retrofit only. Not included with -CA version
ITEMS REQUIRED (Purchase separately)
8 7
Philips Screwdriver
•
Gloves
•
* For App and wireless control set up please refer to the quick start guide or website.
When using product, basic precautions should always be followed, including the following:
Heed all warnings, including below warnings AND those included on product.
•
HALO™ recessed luminaires (fixtures) are designed to meet the latest NEC requirements and are certified in full compliance with UL. Before attempting installation of
•
any recessed lighting luminaire check your local electrical code. This code sets the wiring standards for your locality and should be carefully studied before starting.
Read and follow these instructions.
•
Do not make or alter any open holes in an enclosure of wiring or electrical components during kit installation.
•
To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or other sharp objects.
•
Connect fixture to a 120 volt, 60 Hz power source. Any other connection voids the warranty.
•
Fixture should be installed by persons with experience in household wiring or by a qualified electrician. The electrical system, and the method of electrically connecting
•
the fixture to it, must be in accordance with the National Electrical Code and local building codes.
WARNING - Risk of fire or electric shock. Install this kit only in luminaires that have the construction features and dimensions shown in the photographs and/or drawings
•
and where the input rating of the retrofit kit does not exceed the input rating of the luminaire.
Risk of Fire - MINIMUM
90°C SUPPLY CONDUCTORS. If
uncertain, consult an electrician.
Risk of Electric Shock -
To avoid possible electrical shock,
be sure that power supply is
turned off at fuse box or circuit
breaker before installing or
servicing luminaire.
6 5 4
A. LED module and connector
6 5 4
IMPORTANT SAFETY INSTRUCTIONS
Risk of Fire/Electric
Shock - LED Retrofit Kit
installation requires knowledge
of luminaires electrical systems.
If not qualified, do not attempt
installation. Contact a qualified
electrician. Luminaire wiring and
electrical parts may be damaged
when drilling for installation
of LED retrofit kit. Check for
enclosed wiring and components.
3 2
REVISIONS
REV. DESCRIPTION DATE CHANGE_NUMBER
C. #8-32 Self tapping screw (included)
D. #8-32 Screw (included)
E. #8-32 Hex Nut (included)
ELECTRONIC CAD DRAWING. DO DIMENSIONS THAT AFFECT DENOTES CRITICAL DENOTES FIRST PIECE
S C P
NOT REVISE MANUALLY. SAFE HANDLING OR DIMENSIONS AND AND IN-PROCESS
OPERATION GAUGE CHECK POINTS INSPECTION
DIMENSIONS ARE IN INCHES
DIMENSIONS IN [ ] ARE IN MM
TOLERANCE GENERAL APPROVALS DATE
ENGLISH (IN) .X ± 0.040
.XX ± 0.020
DRWN:
.XXX ± 0.010
METRIC (MM) .X ± 1
.XX ± 0.5
.XXX ± 0.25
CHKD:
ANGLES ALL
± 1.0 °
APPR:
TITLE:
THIRD ANGLE PROJECTION
x.x
L MOD: E9917666
8/17/2020
x.x
MATERIAL: FINISH:
SIZE: DWG NO: Draw1
D
DEV/ZINT NO:
PART NUMBER DO NOT SCALE DRAWING
SURFACE AREA: 439.400 IN2 SCALE: WT: 0.454 LB
3 2
1
BY APPROVED
F
E
D
C
B
DENOTES FIRST
F
PIECE
INSPECTION ONLY
A
REV:
-
VOL: 12.579 IN3 SHEET 1 OF 1
1 IP LEVEL:
Risk of Fire/Electric Shock
LED connector is compatible with
•
Halo 5" H550 Series and 6" H750
and H2750 Series LED Housings
LED connector meets California
•
Title-24 high-efficacy luminaire
standard as a non-screw base
socket.
LED connector is a non-screwbase
•
luminaire disconnect for tool-less
installation.
Edges may be Sharp -
Wear gloves while handling.