golmar ART 4 LITE/G2+ Guía Rápida página 4

ART 4 LITE/G2+ MONITOR
SAFETY PRECAUTIONS
Always disconnect the power supply
- before installing or making modifications to the device.
.
- The fitting and handling of these devices must be carried out by
. - The wiring must run at least 40 cm. away from any other wiring.
- Do not overtighten the screws on the connector.
- Install the monitor in a dry protected location free from the risk of dripping or splashing water.
- Do not place in humid, dusty or smoky locations, or near sources of heat.
- Before connecting the device to the mains, check the connections between the door panel, power
supply, distributors and monitors.
- Always follow the instructions contained in this manual.
CHARACTERISTICS
( )
*
- Hands-free monitor ("ART 4TH LITE" monitor allow handset communication, too).
- 4,3 " TFT c olo r u screen .
.
- Function push buttons for access and selection of menu function.
- Monitor with simple installation (non-polarised 2 wires bus)
- User menu .
.
- Installer menu .
.
- Image and communication settings menu .
.
- Output auxiliary call repeater (max. 50mA/12V ).
.
- "HZ" input for calls from apartment front door.
.
- Push buttons for door release 1 and 2.
.
- Notification l eds.
.
- Configuration switches to assign the call address
- Function codes to define whether the monitor is master or slave (default: master).
SYSTEM OPERATION
( )
*
- To make a call, the visitor must press the button of the apartment; an audible sound indicates that the call is
being made and door panel LED will turn on. If vocal synthesis is enabled, a 'Call is in progress'
message appears indicating that a call is being made. At this moment, the apartment's monitors receive
the call. If another apartment is called by mistake, press the button for the correct apartment and the first
call will be cancelled.
- Upon receiving the call, the image will appear on the screen of the master monitor (and slave 1, if it exists)
without the visitor knowing and icon displayed on the screen
slave monitors 2 or 3, press one of the buttons of the monitor to display the image
answered within 45 seconds, door panel LED
- To establish communication, press the button below
4TH LITE' you can also pick up the handset). The icon
LED will turn off and the led will turn on. If the monitor is an 'ART 4H LITE' / 'ART 4TH LITE' with icon
on the front : with 'ART 4H LITE' make sure that the hearing aid is between 15 and 25 cm away from the
monitor to ensure maximum audio quality during communication with the door panel (
LITE' monitor, the c ommunication with hearing aids
- Co mmunication will last for 90 seconds or until the button below
pressed or (if the monitor is 'ART 4TH LITE' hang up the handset only if communication has been
established pick up the handset). When communication ends,
will become free. If vocal synthesis is enabled, a 'Communication is finished' message will indicate that the
call is over.
- To open door or of the door panel , press the
1 2
screen during the call or communication processes: one press will activate the lock release for seconds
and door panel LED will also turn on for
message will be indicated on the door panel.
- Detailed operation and configuration of the monitor
INSTAL A L TION OF THE MONITOR
( )
*
( ) For more information, see "TART 4 LITE /G2+ user manual (code 50122
*
https://doc.golmar.es/search/manual/50122623
authorised personnel
.
.
dc
(1 to 128) and end of line.
in green color . To view the image from
. If the call is not
will turn off and the system will become free.
icon sh wn on o the screen or (if the monitor is the 'ART
displayed on the screen in red color, door panel
Note:
with 'ART 4TH
must be by establishing communication with the handset)
on-the-hook icon shown on the screen is
door panel LED will turn off and the system
button below the corresponding icon displayed
3
3 seconds. If vocal synthesis is enabled, a 'Door
, see "TART /G2+" user manual 4 .
623 )".
2
ART 4 LITE/G2+
DESCRIP TION
( )
*
A
B
C
D
M
K
SA
GND
L
HZ
HZ
BUS
BUS
128
codes
SA
DIP 1 to 7
GND Monitor
address
HZ
DIP 8
HZ
EOL
resistor
BUS
OFF = 0
ON = 1
BUS
M
( )
Monitor address (code) setup:
*
Dip1 Dip7: -
Sets the monitor address (addresses to
The switches set to OFF have a zero value. The values of the switches set to ON are shown in the table below. The
monitor code is the sum of the values of the switches set to ON.
Important: Apartment 1 (Dip1 to ON & Dip2-Dip to OFF)
Important: Apartment 2 (Dip1 - Dip to OFF).
Dip8: This activates the end-of-line resistance in the ON position. Activate it in monitors where the bus cable ends.
Deactivate it only in intermediate monitors.
Not : e To define whether the monitor is master or slave, entering the corresponding "Special code":
"0550" Master (factory default),
.
Dip1 to Dip : 7 These assign the address of the monitor to call button on the door panel.
Switches - must remain in the OFF position. 2 7
Apartment 1
ON
on the
1 2 3 4 5 6 7
Dip8: This activates the end-of-line resistance in the ON position. Activate it in monitor
is open'
where the bus cable ends. Deactivate it only in intermediate monitors.
Dip 8 a ON
ON
1 2 3 4 5 6 7
( ) For more information, see "TART 4
*
https://doc.golmar.es/search/manual/50122623
EN
MONITOR
MONITOR
A. Handset (only ART 4TH LITE/G2+ monitor)
E
B. Function buttons, access and selection of menu functions.
The function of each button is shown on the monitor screen with an icon
located just above each button
F
Press to access 'Doctor mode' function (standby monitor):
*
- With the special code '0441' (Doctor mode) already entered (see
special codes i n manual "TART 4 LITE/G2+"
for 1 sec. to access menu to activate/ deactivate the function.
- The push button led
be displayed in the main menu if the function 'Doctor mode' is
G
activated and it will turn off if the function is deactivated.
C. Monitor status LED:
H
Yellow ON: Standby without notification.
I
Red ON: "Do not disturb" Mode a tivated.
D. (only ART 4TH LITE/G2+ monitor)
Cable slot
J
E. Speaker ("hands-free" communication mode).
.
F 4.3" TFT colour screen. .
G. Golmar use.
N H.
Microphone ("hands-free" communication mode).
I. Communication with hearing aids
LITE G2+ monitor). Set the hearing aid switch to the T position.
J.
Raised dots for the visually impaired
In call /communication :
A
Above this raised dot is the 'Start/ nd communication' button
Above these raised dots is the 'Door opening' button
K. Configuration switches.
L.
Installation terminals .
M. Wall mounting connector fixing (x4).
O
N. ("handset communication", only ART 4TH LITE/G2+).
Speaker
D O. ("handset communication", only ART 4TH LITE/G2+).
Microphone
Building / Villa (Nexa Door Panel)
1 1 8 2 ).
Table of values
7 .
Switch number: 1 2 3 4 5
1 8 7 Value when ON :1 2 4 8 16 32 64
Dip 8 a ON
ON
1 2 3 4 5 6 7 8
"0551" Slave 1, "0552" Slave or "0553" Slave . 2
Villa (Soul Door Panel)
*
Not : e To define whether the monitor is master or slave, entering
the corresponding "Special code": "0550" Master (factory
default), "0551" Slave 1, "0552" Slave or "0553" Slave . 2
8
Dip 8 a OFF
ON
8 1 2 3 4 5 6 7 8
LITE /G2+ user manual (code 50122
3
.
(see "TART 4 LITE/G2+" manual) .
), press the button
will blink in white color and the icon will
c
.
(only ART 4H LITE G2+ / ART 4TH
people .
E .
.
ON
6 7
1 2 3 4 5 6 7 8
Example: 0+ 0+4+0+ 16+ 0+0 = 20
Dip 8 a OFF
ON
1 2 3 4 5 6 7 8
3
*
3
Kit Soul / Art Lite 4
Manual
623 )".
EN