Descargar Imprimir esta página

Publicidad

Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

π
WIRE MACHINE GUARD
TOOLS NEEDED
3/8" Masonry
Electric Drill
Drill Bit
(Screw Gun)
POST
Straight Bolt x 2
Curved Bolt x 4
Universal Post
Flange Nut x 4
Prior to installation, read instructions all the way through
and determine guard placement. The included
hardware allows for panels to be installed end to end,
as a 90º corner or as a T-intersection.
NOTE: Be sure to include the additional width
of the posts and mounting plate dimensions
when determining placement.
NOTE: One side of the post features four drill
holes for attaching the door. Make sure to
position the post in the proper orientation if
attaching a door to the other side.
MOUNTING THE POSTS
1. Verify that the first post is positioned in the desired
location. Mark the floor where the holes will be drilled.
2. Using a 3/8" masonry drill bit, drill a hole approximately
3" deep into the floor. (See Figure 1)
Clean out debris and dust from inside the hole, and
fully insert anchor bolt through the mounting plate
and into the hole.
PAGE 1 OF 6
1-800-295-5510
uline.com
13mm Wrench
Concrete Anchor x 4
(10mm x 90mm)
Black Plastic
Lock Washer x 4
Plug x 8
Flat Washer x 4
INSTALLATION
17mm Wrench
PARTS
DOOR
Door
Figure 1
Anchor Bolt
3/8"
Masonry
Bit
3. Slightly tap down the anchor bolt with a hammer
if needed. Slide washer onto anchor bolt. Using a
17mm wrench, tighten the hex nut until the anchor
bolt is secure. Repeat for remaining anchors.
Para Español, vea páginas 3-4.
Pour le français, consulter les pages 5-6.
Self-tapping Screw
5' Models x 6
7' Models x 8
Nut Driver x 1
Door Hasp x 1
PANEL
Panel
0721 IH-5607

Publicidad

loading

Resumen de contenidos para Uline H-5607

  • Página 1 Para Español, vea páginas 3-4. Pour le français, consulter les pages 5-6. π 1-800-295-5510 uline.com WIRE MACHINE GUARD TOOLS NEEDED 3/8" Masonry 13mm Wrench 17mm Wrench Electric Drill Drill Bit (Screw Gun) PARTS POST DOOR PANEL Self-tapping Screw Concrete Anchor x 4...
  • Página 2 (See Figure 4) post. Figure 4 TO COMPLETE ASSEMBLY: Use black plastic plugs to Bolt Head cover any unused bolt holes in the posts. 1 ¡ ¢ ' £ ¤ ¥ ¦ § 1-800-295-5510 uline.com PAGE 2 OF 6 0721 IH-5607...
  • Página 3: Rejas De Alambre Para Maquinaria

    π 800-295-5510 uline.mx Rejas De Alambre Para Maquinaria HERRAMIENTAS NECESARIAS Broca de Llave de 13 mm Llave de 17 mm Taladro Eléctrico Mampostería (Desarmador de 3/8" Eléctrico) PARTES POSTE PUERTA PANEL Tornillos Autorroscantes 4 Anclajes de Concreto 6 para Modelos de 5'...
  • Página 4: Continuación De Instalación

    Cabeza del Perno PARA COMPLETAR EL ENSAMBLE: Use las tapas de plástico negras para cubrir cualquier orificio para perno que haya quedado sin utilizar en los postes. 800-295-5510 uline.mx PAGE 4 OF 6 0721 IH-5607...
  • Página 5: Outils Requis

    π 1-800-295-5510 uline.ca GARDE-FOU MÉTALLIQUE OUTILS REQUIS Mèche à Clé de 13 mm Clé de 17 mm Perceuse électrique maçonnerie (tournevis électrique) de 3/8 po PIÈCES MONTANT PORTE PANNEAU Vis autotaraudeuses Model de 5 pi x 6 Ancrage à béton x 4 Boulon droit x 2...
  • Página 6: Fixation De La Porte Aux Montants

    Rondelle de blocage POUR TERMINER L'ASSEMBLAGE : Utilisez les capuchons en plastique noir pour recouvrir les trous de boulons qui n'ont pas été utilisés dans les montants. 1-800-295-5510 uline.ca PAGE 6 OF 6 0721 IH-5607...