Troubleshooting - Lighting Audio LA-1500BT Manual Del Propietário

Operation
Bluetooth Pairing
1. Pairing
Turn on the Bluetooth mode of your mobile phone, then select the function for
Finding Bluetooth Device. After finding, it will show the name of Bluetooth
Device "LA-BT"; once found, select it and then it will asks you to input a password/
PIN. Input "0000" , then the LCD of the car audio system will display CONNECT.
2. Disconnection/Connection
Disconnecting using the mobile phone
When connected, find the paired Bluetooth device, then press the disconnection
button to disconnect.
When turning the unit on (after Acc of the car was switched off ), the unit will search
for a mobile phone, pair and connect. This will take about 10-15 seconds.
Note: When connected, the mobile phone transfers to the car audio player whenever
dialing takes place; the mobile phone transfers to the car audio player whenever
receiving a call.
3. Dialing options when connected
A) Dial with mobile phone directly.
B) To dial with remote control use the following procedures:
1) Briefly press SEND button.
2) Input telephone number with number buttons 0-9.
3) Briefly press END button to cancel the incorrectly entered number, if necessary.
4) Briefly press SEND to start dialing. The talking time will appear on LCD if
dialing is successful and is received.
C) Redial - Press SEND button on remote control three times, it will show DIALING
on LCD and dial the number. After dialing is completed, talk time will display.
4. Accept/ Reject/ End Call
A) To accept the call, press the SEND button.
B) To reject the call, press the END button.
C) To end the call, press the END button.
Note: When call is ringing, CALLING appears along with then the phone number.
While talking, talk time appears.
5. Talking volume level setting
While talking, use volume control to adjust volume level. This volume level can
not be saved.
6. To transfer the audio of a file played by the Mobile Phone to the Car
Audio Player
If the mobile phone supports A2DP and is capable of playing audio files; when
the Mobile Phone plays an audio file, the playback will be transferred to the Car
Audio Player (For some Mobile Phones, you must first select Play by Bluetooth).
In A2DP mode, if the Bluetooth device of the Mobile Phone supports AVRCP, the
functions of the >>|, |<< and PLAY/PAUSE buttons are the same as in media mode
(no fast forward/backward functions for the >>|/|<< buttons). The other buttons
normally available in media mode are not available.
Android App (LA-1500BT & LA-2300BT)
Another way to control the unit instead of using the included remote, you can use
your Android phone. You will need to install the "RadioView" app onto your mobile
device. The app will need to be downloaded from Google Play. Do a search for
"RadioView" and proceed to download. Install per the app instructions.
All manuals and user guides at all-guides.com
Remote Control
+
-
/ button
POWER
POWER button SEL (Select) button
A.P (Auto Program) UP DN
FWD/BACK, UP/DOWN button
button AP SEL
SCN (Scan) button AF (Alt. Freq.) button
SCN CLK AF
CLK (Clock) button
PTY (Program Type) button
BND (Band) button
TA (Traffic Announcement) button
MODE button
MODE BND PTY TA
TOP INT RPT RDM
PLAY/PAUSE button 1 2 3 4 RDM (Random) button
RPT (Repeat) button
INT (Intro) button
5 6 7 8
NUMBER buttons
" * " button 9 0 " " button
* # #
MUTE
MUTE button Call END button
T-M
T-M button Call SEND button
Load/unloading battery of remote control
B
A
Fig. 1 Fig. 2 Fig. 3
1.
Please remove insulating sheet out of remote control before use. Pull out
insulating sheet in the direction as per Fig. 1.
2. When changing battery for remote control, first pull the movable block hold in
the direction as indicated in Fig. 2, Arrow A. Then pull the battery holder out
from the remote control in the direction as indicated in Fig.2, Arrow B.
3.
Replace the old battery by a new battery with (+) polarity side upward. Then
return the battery holder to the remote control by pressing the battery holder.
Please see Fig.3.
Improper use of battery may cause overheating or
explosion, which may result injury or fire.
Battery leakage may cause damage to the remote
control(Battery Life: 6 months with normal use in
normal room temperature).
• Do not short the battery.
• Do not throw the battery into fire.
• To avoid the risk of accident, keep the battery out of reach of children.
10
Symptom
Source unit does not turn on.
Unit resets itself when engine is off
Tuner fails to tune any stations
illus.-3.1
Unable to tune stations in seek mode
+ Side Up
USB device cannot be inserted
illus.-3.2
USB device is not recognized
No sound heard with the display "No
File" shown
Sound skips or is noisy
MP3 is not playing back
CD skips excessively
Sound skips or is noisy; unable to
fast forward or backward CD
CD Insertion not possible
Diagnosis Remedy
Basic
Blown fuse Check fuse of the unit, replace with correct rating.
If connect following the instructions, the unit will not
Vehicle's ignition is off
operate with ignition off.
Check battery, connection and fuses and repair or
Voltage applied to Red and Yellow wires is not
replace as necessary. If voltage is above +16 volts,
between 10.8 & 16 volts or there is not voltage
have the electrical system inspected by and authorized
present
car service center
Unit is not properly grounded Check wiring and repair as necessary
Incorrect connection between ACC and battery Check wiring and repair as necessary
Radio
No antenna or disconnected or open connection
Check all connections and repair as necessary
in cable
You are in a weak signal area Make sure the tuner LOC mode is off
USB Devices
The USB device has been inserted with wrong Reversing the connection direction of the USB device,
direction try it again
The USB device connector is broken Replace with a new USB device
Disconnect USB device an reconnect. If the device is
The USB device is damaged
still not recognized, try replacing with a different USB
Connectors are loose
device
No MP3/WMA files are not stored on the USB
Store these files properly on the USB device
device
MP3/WMA files are not connected properly Use MP3/WMA files encoded properly
MP3
Writing error occurred. The MP3 format is not
Make sure MP3 has been written in a supported format
compatible.
CD Player (LA-2300BT only)
Check mounting angle of source unit (Mount within
Source unit mounted at an incorrect angle + or - 20 degrees from horizontal) and repair as
necessary.
Source unit not secured properly (Standard Check tightness of installation sleeve and back strap;
Mount) repair or replace as necessary.
Check tightness of mounting screws and repair or
Source unit not secured properly (ISO Mount)
replace as necessary.
Compact disc is dirty Clean disc with soft cloth
Compact disc is heavily scratched or warped Replace with new disc without scratches
A CD is already in the CD player Press the eject button to remove disc
11

Troubleshooting