Electrical Requirements - Morphy Richards 47910 Manual De Instrucciones

47910MEE Rev1:Layout 2

ELECTRICAL REQUIREMENTS

Check that the voltage on the rating plate of your appliance
corresponds with your house electricity supply which must
be A.C. (Alternating current).
WARNING: This appliance must be earthed.
UK only
For appliances with fitted plug.
If the socket outlets in your home are not suitable for the
plug supplied with this appliance the plug should be
removed and the appropriate one fitted.
IMPORTANT : THE PLUG REMOVED FROM THE MAINS
LEAD, IF SEVERED, MUST BE DESTROYED AS A PLUG
WITH A BARED FLEXIBLE CORD IS HAZARDOUS IF
ENGAGED INTO A LIVE SOCKET OUTLET.
Where used, should the fuse in the 3 amp plug require
changing a 13 amp BS1362 fuse must be fitted.
Features
⁄ Lid
¤ Coffee bean container
‹ Coffee bean grind and coarseness setting
› Cup selector
fi Illuminated on /off power indicator.
fl Start/stop button
‡ Coffee grinds container
NOTE: The grinder has a 12 cup capacity bean grind.
Operating the Appliance
1 Remove the Coffee Bean container lid.
2 Fill the coffee bean container with required amount of
beans, making sure that the lid closes securely.
(The maximum fill is 225g or 8 ounces of beans.)
3 Set the grind selector to the desired grind size by turning
the bean container. A – see table in grinding times and
selection for more information.
4 Position the dial to the desired number of cups you require
coffee grinds for, (2 -12 cups max.) B
5 Plug cord into power outlet.
6 Press power button to turn bean grinder on, the power will
not turn on unless both containers are fitted into the main
unit correctly.
• Please take into account that based on your personal
preference you can make your coffee weaker or stronger by
adjusting cup selection to reduce or increase the amount of
fresh coffee grinds produced.
7 Press the start / stop button to begin bean grinding, this
will flash during the grinding operation. A safety feature of
your bean grinder is that the grinder will not operate unless
the coffee bean container is fully in place in the grinder
mechanism.
8 The grinder will automatically stop when the correct
amount of coffee has been ground with coffee grinds
4
3/8/09 12:18 Page 4
deposited in the coffee grinds container.
9 To manually stop the grinding operation during use, press
the stop / start button. To re-start, repeat steps 6 & 7.
10 Remove the coffee grids container, make your coffee with
the fresh grinds, sit down and enjoy.
Grinding times & grind selection
Your new Morphy Richards coffee bean grinder is a fully
automatic Burr grinder.
The grinding time is automatically adjusted to suit the
coarseness setting and cup selection setting to ensure the
amount of grounds is accurate for each grind.
Please note that some finite adjustment may be required
depending on the coffee beans used.
The grinder guide below provides an indication of which
grind is most suited to the type of coffee maker to be used.
The table should be used as a guide and settings adjusted to
suit your particular coffee maker and taste.
Please note that the coarseness setting is particularly critical
when grinding for use in espresso machines; too fine a
grind may reduce the flow and over extract the coffee, too
coarse a grind may increase the flow and under extract the
coffee. Both can result in poor tasting coffee with little or no
crema, adjust the grind size to suit your particular espresso
maker.
Remember never to grind more coffee beans than you need
for use in the next hour as ground coffee rapidly oxidises
and is quickly spoilt.
If you grind more coffee than necessary, it can be kept for a
short length of time, in a sealed container in the fridge.
Setting Grinds suitable for
Fine Espresso - Pump or Steam
Medium Filter Coffee Maker / Moka pots / Stove Tops
Coarse French Press / Plunger / Cafetiere
Cleaning Your Grinder
Ensure that the bean grinder is unplugged.
The coffee bean grinder is not dishwasher safe.
All removeable parts can be washed in warm soapy water.
Ensure all washed parts are completely dry before
replacing.
Never immerse the grinder base unit in water or any other
liquids. To clean the grinder base unit wipe with a wet
cloth and use a soft cleaning brush to remove excess
grinds.
HELPLINE
If you have any difficulty with your appliance, do not hesitate
to call. We are more likely to be able to help than the store
from where you bought it.
Please have the following information ready to enable our