Resumen de contenidos para MGA Entertainment Little Tikes Waterfall Island
Página 1
years Waterfall Island Water Table ™ ASSEMBLY INSTRUCTIONS #659157M8 Adult assembly required. Approx. assembly time: 30 min. Look for video of assembly on www.youtube.com/littletikes or our website at www.littletikes.com/videoinstructions XIM659157 - 11/21...
Página 4
Table Top (1) Table Legs (3) Basin Support (1) Basin (1) Axle (1) Paddle Cover (1) Waterfall Tube Waterfall Tube (1) with Hole (1) Waterfall Base Waterfall Base - - Left (1) Right (1) Slide Bottom (1) Slide Top (1) Palm Tree Palm Tree Top (2) Base (2)
Página 5
Pull the drain plug...all the way! First insert the drain plug (part Q) into opening on table top (part A). Push drain plug through the opening. Next, flip table over. Work the plug around the opening, pulling only the plug edge through. Recommended (not included) The plug edge...
Página 6
Attach the legs Insert 3 table legs (part B) into table Assembly Hint: 1 tbsp. top (part A), snap into place. of liquid soap Place on flat surface before you push legs in Attach the support Insert the basin support Secure using (2) "...
Página 7
It’s time for the palm trees! Snap palm tree top (M) onto palm tree base (N). Repeat for the second palm tree. Spins! Part is keyed to fit Align notches on palm tree assembly to notches on base. Press to fit each palm tree into table.
Página 8
Build a waterfall, oh my! (2) 3/4" (1.9 cm) Fit together the waterfall tube with the hole (part F) to the the waterfall tube (part G). Install (2) 3/4" (1.9 cm) screws to secure. Fit it together... Fit the notches on the waterfall base-RIGHT Fit the assembled waterfall tube (part J) to the holes in the waterfall tube.
Página 9
Fit it together... (8) 3/4" (1.9 cm) Install (8) 3/4" (1.9 cm) screws to secure. Time for the slide (2) 3/4" (1.9 cm) Install (2) 3/4" (1.9 cm) screws to secure. Press slide top (part K) onto slide bottom (part L).
Página 10
Slide on... Align the slide assembly with the indent on the waterfall assembly and fit into place. Look underneath, slide edge should be fitted inside tabbed ridge. Let's SNAP it together! Place the waterfall/slide assembly onto the center slots on the table top.
Add the basin..(1) 3/4" (1.9 cm) TOP VIEW Place the basin (part D) onto the tops of the waterfall and basin support. Install (1) 3/4" (1.9 cm) screw to secure. Time to spin around and around! SNAP the paddle (part O) onto one end of the axle (part E). SNAP the squid cap (part P) onto the other end of the axle (part E).
Página 12
PADDLE SQUID CAP Place the assembled spinner onto the table (as shown). The squid cap should be facing outward. The paddle should be on the inside the table. Cover it! Ridge MUST FACE outer edge. Place paddle cover (part H) over spinner assembly.
Página 13
Let's play! Fill with approximately 5.27 gallons (19.95 liters) of water when ready to play! The treasure chest can fit in either the in boat deck area or under the waterfall/slide assembly. Boat deck cover (part R) fits over opening on table. Treasure chest cover (part S) fits over opening under waterfall/slide assembly.
Fasi di assemblaggio Informazioni molto importanti da considerare! • Leggere prima tutte le istruzioni. Fase 1: Tirare il tappo di scarico... completamente! • Liberare una superficie piana per disporre tutti i materiali in modo che 1. Innanzitutto, inserire il tappo di scarico (parte Q) nell’apertura sulla tutto sia a portata di mano.