Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

WARNING:
Do not allow familiarity with products
to make you careless. Remember that a careless
fraction of a second is sufficient to inflict serious
injury.
WARNING:
Always wear eye protection with side
shields marked to comply with ANSI Z87.1. Failure to
do so could result in objects being thrown into your
eyes resulting in possible serious injury.
WARNING:
Do not use any attachments or
accessories not recommended by the manufacturer
of this product. The use of attachments or
accessories not recommended can result in serious
personal injury.
APPLICATIONS
You may use this product for the purpose listed below:
 Charging compatible 12 Volt - 19.2 Volt Craftsman
battery packs
CAUTION:
If at any point during the charging
process none of the LEDs are lit, remove the
battery pack from the charger to avoid damaging
the product. DO NOT insert another battery. Return
the charger and battery to your nearest authorized
service center for service or replacement.
CAUTION:
Charge in a well ventilated area. Do not
block charger vents. Keep them clear to allow proper
ventilation.
LED FUNCTIONS OF CHARGER
See Figures 2 - 3, pages i - ii.
CHARGER LED WILL BE ON TO INDICATE
STATUS OF CHARGER AND BATTERY PACK:
 Red LED on, Green LED off = Power to charger is on.
 Red LED flashing, Green LED off = Battery is being
tested.
 Red LED fading, Green LED off = Battery is defective.
 Red LED on, Green LED flashing = Battery is charging.
 Red LED off, Green LED on = Battery is fully charged.
 Red LED off, Green LED fading on and off = Battery
is fully charged; charger is in Energy Save mode.
Charger will periodically wake from Energy Save mode
to ensure the battery pack remains in a fully charged
state.

OPERATION

CHARGING A BATTERY PACK
Battery packs are shipped in a low charge condition to
prevent possible problems. Therefore, you should charge
them before first use. If the charger does not charge the
battery pack under normal circumstances, return both the
battery pack and charger to your nearest repair center for
electrical check.
 Make sure the power supply is normal household
voltage, 120 volts, AC only, 60 Hz.
 Connect the charger to a power supply.
 Attach the battery pack to the charger by aligning the
raised ribs on the battery pack with the grooves in the
charger, then slide the battery pack onto the charger.
 Press down on the battery pack to be sure contacts on
the battery pack engage properly with contacts in the
charger.
 Latches should snap into place to ensure battery is
correctly connected.
®
 Do not place the charger in an area of extreme heat or
cold. It will work best at normal room temperature.
NOTE: The charger and battery pack should be placed
in a location where the temperature is more than 50°F
but less than 96°F.
 The battery pack will become slightly warm to the
touch while charging. This is normal and does not
indicate a problem.
 After charging is complete, the green LED will remain
on for one hour, indicating Maintenance Mode.
 After completing maintenance mode, the green LED
will begin fading on/off continuously. This indicates the
battery is fully charged and the charger is in Energy
Save Mode.
 Charger will periodically wake from Energy Save mode
to ensure the battery pack remains in a fully charged
state.
 To remove the battery pack from the charger, depress
the latches on both sides of the battery pack and pull
up on the battery pack.
CHARGING A HOT BATTERY PACK
When using a tool continuously, the battery pack may
become hot. A hot battery pack may be placed directly
onto the charger port but charging will not begin until
the battery temperature cools to within acceptable
temperature range. When a hot battery pack is placed
on the charger, the red LED will begin flashing and the
green LED will be off. When the battery pack cools to
approximately 120°F (40°C), the charger will automatically
begin charging.
6 — English

Publicidad

Tabla de contenido
loading

Tabla de contenido