GENERGY Sella Instrucciones De Uso página 31

ITALY
First Choice When Quality Matters
W
• Manifold:
- Forged Brass: New high efficiency design concept.
(Patented) Strength and no porposity = long life.
Higher Hydrostatic Pressures - Safety, Performance.
- Unloader: Integral trap pressure, fixed
chemical injector. Simple repair using a cartridge
replacement kit with built in EZ start valve.
- Inlet and Discharge Ports: Heavy bosses for added
strength. 3.8"F Inlet and 3/8"M discharge.
- Offset Discharge Ports: High efficiency, smooth
flow.
- Bolts: 8 Bolts, 10mm, grade 8.8
• Valves:
- Ultra Form Cages: Durable, strength, and long
life.
- Poppets, Seat and Spring: 303 and 400 series
stainless steel.
- Valve Caps: Machined brass - greater strength.
• Packing and Plungers:
- High and Low Pressure Packing: "V" style (D-
1) Buna-N (cotton duct weave base) strong and
tightens under load.
- Support and Guides: Machined brass, 1-piece
construction and special packing support ring to
assure proper plunger alignment and to maximize
packing and seal life.
- Plungers: Ceramic coated stainless steel.
- Low Pressure Seals: "U" cup double lip Buna-N,
good positive seal.
D
• Bearings: Oversized for maximum life and load
disbursement, needle bearing on the drive side and
ball on the non-drive side. Each bearing is held in
position on the crankshaft and crankcase by snap
rings. This assures positive alignment and centering
of the connecting rods and crankshaft in relation
to the crankcase, it also eliminates the crankshaft
from floating.
• Crankcase: Precision die-cast, large cooling fins
and anodized (for maximum heat dissipation).
• Rear Cover: Precision stamped steel O-Ring
seal.
It is prohibited to reproduce, copy or use this document without written permission from Stock Garden Spain (GENERGY), Spain, 2009.
GAS POWERED PRESSURE WASHER
S
PECIAL
E
ET ND
E
RIVE ND
M : RSV4G40D-F40 - 3400
ODEL
F
EATURES
• Plunger Rods: Stainless steel construction for
strength (no plating to scrape off), O-Ring plunger
sealing system.
• Rod Pins: Precision ground and hardened steel,
oversized for load disbursement.
• Connection Rods: One piece special allow
aluminum and bronze based, oversized for
maximum strength, load disbursement, and
life. Heavy pin area construction, for added load
strength.
• Crankshaft: Forged, precision ground and
hardened for extremely long life and durability.
Available in 3/4" and 1" hollow shafts. Shaft key
set screw are standard on high speed version for
long shaft life.
• Oil Seals and O-Rings: All are constructed of
Buna-N rubber. The O-Rings have stainless steel
garder springs to assure constant tension on the
sealing surface.
• Ports and Oil Drain: One 1/4" discharge
accessory port and on 1/4" inlet accessory port.
One crankcase bottom drain plug.
• Oil Capacity: 16 oz.
E
XTRA
• Dyno Proven: All pumps are dyno tested to
assure the theroretical design meets the actual
design.
• Valve Design: Each pump series has a valve
design that optimizes its highest efficiency.
• Wet End Repair: Very simple no special tools
are required.
• Mounting Flanges: SAE j609A and j609B
• Design Uses: Using Advanced Fluid Handling
Design Programs, overall pump efficiency is
increased.
RPM
F
EATURES
31