Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
BEFORE
STARTING
ENGINE
ADD OIL
Your lawnmower
is shipped
without
oil in
the engine.
For type and grade of oil to
use, see "ENGINE"
in the Maintenance
section
of this manual.
A CAUTION:
DO NOT overfill
engine with
oil, or it will smoke
heavily
from the muffler
on startup.
1.
Be sure lawnmower
is level.
2.
Remove
oil dipstick
from oil fill spout.
3. You receive
a container
of oil with the
unit.
Slowly
pour the entire container
down the oil fill spout into the engine.
NOTE:
Initial oil fill requires
only 18 oz.
due to residual
oil in engine from the
manufacturers
100% quality
testing.
When
changing
oil you may need 20 oz.
4.
Insert and tighten
dipstick.
IMPORTANT:
• Check
oil level before
each use.
Add oil
if needed.
Fill to full line on dipstick.
• Change
the oil after every 25 hours
of
operation
or each season.
You may
need to change
the oil more often
under dusty, dirty conditions.
See "TO
CHANGE
ENGINE
OIL" in the Mainte-
nance section
of this manual.
ADD GASOLINE
• Fill fuel tank to bottom
of tank filler neck.
Do not overfill.
Use fresh, clean,
regular
unleaded
gasoline
with a minimum
of
87 octane.
Do not mix oil with gasoline.
Purchase
fuel in quantities
that can be
used within 30 days to assure
fuel fresh-
ness.
A CAUTION:
Wipe off any spilled
oil or
fuel.
Do not store,
spill or use gasoline
near an open flame.
A_, CAUTION:
Alcohol
blended
fuels
(called gasohol
or using ethanol
or metha-
nol) can attract
moisture
which leads to
separation
and formation
of acids during
storage.
Acidic gas can damage
the fuel
system
of an engine
while in storage.
To
avoid engine
problems,
the fuel system
should
be emptied
before storage
of 30
days or longer.
Empty
the gas tank, start
the engine
and let it run until the fuel lines
and carburetor
are empty.
Use fresh fuel
next season.
See Storage
Instructions
for
additional
information.
Never use engine
or carburetor
cleaner
products
in the fuel
tank or permanent
damage
may occur.
Engine
oil cap
Gasoline
filler cap
Primer
TO STOP
ENGINE
• To stop engine,
release
operator
pres-
ence control
bar.
TO START
ENGINE
NOTE:
Due to protective
coatings
on the
engine,
a small amount
of smoke
may be
present
during the initial use of the product
and should
be considered
normal.
1. To start a cold engine,
push primer
three (3) times before
trying to start.
Use a firm push. This step is not usu-
ally necessary
when starting
an engine
which has already
run for a few minutes.
2. Hold operator
presence
control
bar
down to the handle and turn the start
key.
IMPORTANT:
Do not crank engine more
than five continous
seconds
between
each
time you try to start. Wait 5 to 10 seconds
between
each attempt.
• To start engine
using the rope starter,
follow the steps above.
Exchange
the
use of the starter
rope for start key.
Pull starter
handle
quickly.
Do not allow
starter
rope to snap back.
NOTE:
In cooler weather
it may be neces-
sary to repeat
priming
steps. In warmer
weather
over priming
may cause flooding
and engine will not start. If you do flood
engine
wait a few minutes
before
at-
tempting
to start and do not repeat
priming
steps.
11
Publicidad
Tabla de contenido
