Crest Audio Pro-LITE 5.0 Manual Del Propietário página 34

Pro-LITE
Rated Watts 2ch x 2 ohms
Rated Watts 2ch x 4 ohms
Rated Watts 2ch x 8 ohms
Minimum Impedance
Maximum RMS Voltage Swing
Frequency Response
20Hz - 20kHz 2ch x 2 ohms
20Hz - 20kHz 2ch x 4 ohms
20Hz - 20kHz 2ch x 8 ohms
Input CMRR
Voltage Gain
Crossover
Crosstalk
Hum and Noise
Slew Rate
Damping Factor (8 ohms)
Phase Response
Input Sensitivity
Input Impedance
Current Draw @ 1/8 in VA (watts)
Current Draw @ 1/3 in VA (watts)
Idle Consumption
Cooling
Controls
Indicator LEDs
Protection
Connectors
Construction
Dimensions
Net Weight
Gross Weight
Rated power readings made with BW: 20 Hz to 22 kHz. All power measurements made @ 120 VAC or 240VAC.
2 ohm steady state sine wave power is time limited by circuit breaker.
Bridge operation is not possible.
*Net Weight does not include power cord.
5.0 Specification Sheet
®
3300 watts 20ms repetitive burst / 2600 watts 1% THD both channels driven @ 1kHz.
2025 watts 20ms repetitive burst / 1725 watts 1% THD / 1500 watts 0.2% THD, both channels
driven @ 1kHz.
1175 watts 20ms repetitive burst / 1000 watts 1% THD / 825 watts 0.2% THD, both channels
driven @ 1kHz.
2 ohms
105 volts
20Hz - 22kHz; +/-0.5dB @ 1watt.
<0.5% @ 2250 watts 20Hz to 4kHz, decreasing to 1650 watts @ 20kHz, both channels driven.
<0.15% @ 1400 watts 20Hz to 10kHz, decreasing to 1350 watts @20kHz, both channels driven.
<0.15% @ 860 watts 20Hz to 4kHz, increasing to 1000 watts @ 20kHz, both channels driven.
> - 75dB @ 1 kHz.
x 40 (+32dB)
100Hz switchable 2nd order high pass and 3rd low pass per channel.
> -60dB @ 1kHz @ 700 watts power @ 8 ohms.
> -105dB, "A" weighted referenced to rated power @ 4 ohms.
> 12V/μs
> 210:1 @ 20Hz - 1kHz @ 8 ohms
+5 to -91 degrees from 20Hz to 20kHz
1.95 volts +/- 3% for 1kHz 4 ohm rated power, 1.83 volts +/- 3% for 1kHz 2 ohm rated power
20 kilohms, balanced and 10 kilohms unbalanced.
1435 (890) @ 2 ohms, 920 (525) @ 4 ohms, 625 (335) @ 8 ohms
3050 (2155) @ 2 ohm, 1880 (1200) @ 4 ohms, 1200 (715) @ 8 ohms
195VA, 90 watts.
3 temperature dependent variable speed fans.
2 front panel attenuators, crossover select switch for HPF, Normal and LPF
Five LED indicators per channel: Active, Signal, ACL, Temperature and DC
Thermal, DC, subsonic, incorrect loads, under and over voltage
Inputs: Dual combination 1/4" XLR, Outputs: Dual 1/4" thru, one 2- pin & one 4 pin twist-lock
connector
0.062" thick aluminum
3.5"x19"x 17" behind front panel + 0.6" for handle
6.2kg (13.6lbs.*)
7.9kg (17.4lbs.)
34