Intended Use - Stomer Professional SFS-223 Instrucciones De Servicio

English
Finishing sander

INTENDED USE

This tool is intended for dry sanding and fi nishing of wood,
painted surfaces, plastic and fi ller
TECHNICAL SPECIFICATIONS
PRODUCT ELEMENTS
1 On/Off switch
2 Dust bag
SAFETY
WARNING! Read all instructions. Failure to follow all in-
structions listed below may result in electric shock, fi re
and/or serious injury.
● Avoid damage that can be caused by screws, nails and
other elements in your workpiece; remove them before
you start working
● Always keep the cord away from moving parts of the
tool; direct the cord to the rear away from the tool
● When you put away the tool, switch off the motor and
ensure that all moving parts have come to a complete
standstill
● Use completely unrolled and safe extension cords with
a capacity of 16Amps (U.K. 13Amps)
● In case of electrical or mechanical malfunction, imme-
diately switch off the tool and disconnect the plug
● SBM Group can assure fl awless functioning of the tool
only when original accessories are used
● This tool should not be used by people under the age
of 16 years
● The noise level when working can exceed 85 dB(A);
wear ear protection
● If the cord is damaged or cut through while working, do
not touch the cord, but immediately disconnect the plug
● Never use tool when cord is damaged; have it replaced
by a qualifi ed person
● Always check that the supply voltage is the same as
the voltage indicated on the nameplate of the tool (tools
with a rating of 230V or 240V can also be connected to a
220V supply)
● This tool is not suitable for wet sanding
● Do not work materials containing asbestos (asbestos is
considered carcinogenic)
● When sanding metal, sparks are generated; do not use
dustbox and keep other persons and combustible material
from work area
● Do not touch the moving sanding sheet
● Do not continue to use worn, torn or heavily clogged
sanding sheets
● Wear protective gloves, safety glasses, close-fi tting
clothes and hair protection (for long hair)
● Take protective measures when during work dust can
develop that is harmful to one's health, combustible or ex-
plosive (some dusts are considered carcinogenic); wear a
dust mask and work with dust/chip extraction when con-
nectable
1
2
● Always disconnect plug from power source before
making any adjustment or changing any accessory
WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):
● Do not connect the blue (= neutral) or brown (= live)
wire in the cord of this tool to the earth terminal of the plug
● If for any reason the old plug is cut off the cord of this
tool, it must be disposed of safely and not left unattended
● the dust suction requires the use of perforated sanding
sheets
● perforation in sanding sheet should correspond with
perforation in sanding foot
● replace worn sanding sheets in time
● always use the tool with the total sanding surface
covered with sanding paper
● before the sanding surface reaches the workpiece, you
should switch on the tool
● before switching off the tool, you should lift it from the
workpiece
● do not apply too much pressure on the tool; let the
sanding surface do the work for you
Your machine is double insulated in accordance with EN
50144; therefore no earthwire is required.
MAINTENANCE
Make sure that the machine is not live when car-
rying out maintenance work on the motor.
Regularly clean the machine housing with a soft cloth,
preferably after each use. Keep the ventilation
slots free from dust and dirt.If the dirt does not
come off use a soft cloth moistened with soapy
water. Never use solvents such as petrol, alcohol, ammo-
nia water, etc. These solvents may damage the plastic
parts.
The machine requires no additional lubrication.
Should a fault occur, e.g. after wear of a part, please con-
tact your local SBM Group dealer.
ENVIRONMENT
In order to prevent the machine from damage during
transport, it is delivered in a sturdy packaging. Most of the
packaging materials can be recycled. Take these materi-
als to the appropriate recycling locations. Take your un-
wanted machines to your local SBM Group dealer. Here
they will be disposed of in an environmentally safe way.
4