Korg KONNECT Manual De Usuario página 4

Part names and functions
5
3
1
6
4
2
7
1
(Power) button, LED: The power will turn on (the LED will light) or the unit
will switch to Standby (the LED will blink) when the button is pressed.
2 DC INPUT jack: The included AC adapter is connected here.
3 MASTER VOLUME knob, CLIP LED: Adjusts the volume of the KONNECT. Rais-
ing the volume too high may cause the sound outputted from the speaker to sound
unnaturally distorted, and the CLIP LED may light. If this happens, adjust the
volume with the MASTER VOLUME knob until the CLIP LED goes dark.
4 REVERB LEVEL & TYPE knob: The reverb type and effect depth can be adjusted,
according to the position of this knob. When this knob is fully turned to the left, the
reverb will be turned off.
5 LIMITER LED: This LED lights when the limiter is in operation. If the volume is
raised too high, the LIMITER LED will light, and the volume will be automatically
limited.
6 FEEDBACK SUPPRESSOR button, LED: This switches the FEEDBACK SUPPRES-
SOR on (the LED will light) or off. Turning this on will cause feedback to be sup-
pressed. (Available only in the channels 1 and 2)
7 (Bluetooth) pairing LED: This LED lights when the KONNECT is connected to
an external device via Bluetooth. (Refer to "Connecting to the KONNECT App via
Bluetooth".)
8 Channel selection buttons and LEDs: Selects the channel that will be controlled
by the channel VOLUME, VOICING knobs. The LED for the selected channel will
light.
Tip: When playing back music from an external device connected via Bluetooth, input chan-
nels 3 and 4 (3/4) are used.
9 VOLUME knob, CLIP LED: This adjusts the volume of the channel that was se-
lected using the channel selection buttons. If the levels going into the channel are
excessive, the CLIP LED will light. If this happens, lower the volume of the device
on the channel, until the CLIP LED goes dark.
10 VOICING knob: The VOICING type and effect depth can be adjusted, according to
the position of this knob.
Tip: "VOICING" includes the optimal equalizer settings that match the characteristics of
each device connected to the KONNECT and the background music to be played.
11 CENTER CANCEL button, LED: This switches center cancel on (the LED will light)
or off for channels 3/4. When center cancel is switched on, the volume for only the
vocals or guitar sounds in music played by devices that are connected to the KON-
NECT can be decreased.
12 MIC and MIC/LINE input jacks for channel 1: Use this input for dynamic mics
or LINE output level devices.
13 MIC/LINE switch: Switches between either MIC level or LINE level on the MIC/
LINE input jack for channel 1.
Tip: When connecting a passive-type guitar or other instrument (one that does not use a
preamp), connect the instrument to a commercially available preamp or effector first,
and then connect the preamp to the LINE input jack of the KONNECT.
14 MIC and LINE input jacks for channel 2: Use this input for dynamic mics and
LINE output level devices.
15 STEREO INPUT jack for channels 3/4: Use this jack to input a stereo LINE output
level device into channels 3/4.
16 L/MONO INPUT and R INPUT jack for channels 3/4: Use these jacks for inputting
the L and R signals from a LINE output level device. (When using just the L/MONO
INPUT jack, channel 3/4 will operate as a single channel in monaural mode.)
Connections
1 Turn the MASTER VOLUME knob on the KONNECT to the minimum position.
2 Connect the included AC adapter to the DC INPUT jack, and then plug the AC
adapter into an AC outlet.
The KONNECT will enter Standby mode, and the power LED will blink.
Use only the AC adapter provided with your KONNECT. Using a different adapter may
cause malfunctions or other issues.
8
9
12
10
8
14
8
11
15 16
Setup
3 Connect your external device(s) into the channel input jacks.
4 Press the power button to turn on the KONNECT.
13 Tip: To return to Standby mode, press the power button once more.
5 Slowly turn the VOLUME and MASTER VOLUME knobs to adjust the volume.
Auto power-off function
The KONNECT has an auto power-off function. With this function, the unit auto-
matically enters standby mode if there is no operation and input for approximately 20
minutes.
REVERB TYPE
SMALL: This reverb setting simulates a small room, such as a home studio.
MEDIUM: This reverb setting simulates a medium-sized room, such as a live
music club.
LARGE: This reverb setting simulates a large room, such a concert hall.
LARGE & BRIGHT: This reverb setting simulates a large room with a clear sound.
VOICING TYPE
MUSIC (GENERAL): This is the standard setting when listening to music at home.
MALE VOCAL:
FEMALE VOCAL:
ELECTRIC GUITAR: This is the optimal setting for electric guitars.
ACOUSTIC GUITAR: This is the optimal setting for acoustic guitars.
Tip: You will be able to select more voicings when using the KONNECT App.
Connecting to the KONNECT App via Bluetooth (Pairing)
For points of caution and detailed methods of operation when pairing, refer to the
KONNECT App download website, or the "Quick Guide" located in the app itself.
1 While the KONNECT is on, hold down the channel selection button for channel
3/4.
The (Bluetooth) pairing LED will blink, and the KONNECT will enter Bluetooth
pairing standby mode.
2 Following the settings on your external device for Bluetooth connection, select
"KONNECT" as the connection point.
When pairing is complete, the LED will light, and you will be able to control the
various operations and play back music on the KONNECT from the app.
When an analog device is connected to channels 3/4, the playback from the analog device
will be given priority. When playing back on a Bluetooth device, disconnect the cable
from the analog device to the KONNECT.
For more information on which devices and OS versions that the KONNECT App is
compatible with, refer to the download website for the app, and the "Quick Guide" lo-
cated in the app itself.
3 To cancel pairing standby mode, hold down the channel selection button for
channel 3/4.
Number of REVERB types: 4
Number of VOICING types: 5 (many types are available when using the KONNECT App)
Wireless method:
Input jack: Channel 1
Channel 2
Channels 3/4
Speakers:
Power amp output:
Power Source:
Current consumption
Dimensions:
Weight:
Accessories:
Optional Item:
* Appearance and specifications of this product are subject to change without notice.
- 4 -
This is the optimal setting for male vocals or speech.
This is the optimal setting for female vocals or speech.
Specifications
Bluetooth (A2DP Sink), Bluetooth low energy
MIC input jack: (XLR type [balanced], 6 kΩ,
specified level -20 dBV)
MIC/LINE input jack: (6.3 mm monaural phone jack
[unbalanced], MIC: 3.5 kΩ, specified level -20 dBV, LINE:
7.5 kΩ, specified level 0 dBV)
MIC input jack: (XLR type [balanced], 6 kΩ,
specified level -20 dBV)
LINE input jack: (6.3 mm monaural phone jack [unbal-
anced], 7.5 kΩ, specified level: 0 dBV)
L/MONO INPUT jack: (6.3 mm monaural phone jack
[unbalanced], 15 kΩ/ 7.5 kΩ, specified level: 6 dBV)
R INPUT jack: (6.3 mm monaural phone jack [unbalanced],
15 kΩ, specified level: 6 dBV)
STEREO INPUT jack: (3.5 mm stereo mini phone jack
[unbalanced], 15kΩ, specified level: 6 dBV)
6.5-inches and 1-inch x 2 (16.5 cm and 2.5 cm x 2)
Maximum approx. 140 W and 20 W x2
AC adapter (DC 20V or 24V:
1.5A
452 x 225 x 232 mm / 17.80 x 8.86 x 9.13 inches (W x D x H)
5.3 kg / 11.68 lbs.
AC adapter, Owner's Manual
Speaker Stand (ST-S80)
)