lauson EH204 Manual De Instrucciones

EN
BLUETOOTH EARPHONE
EH204
USER MANUAL
Brief Introduction
1. Previous song, volume up
2. Microphone
3. LED indicator
4. Power on/off, play/pause, redial
5. Next song, volume down
6. Micro USB charging port
1
Basic Use:
(Button #4)
1. To turn the earphones on: press and hold the power button
until the blue LED blue and red light starts alternately flashing,
then release it.
2. To turn the earphones off: press and hold the power button
until the Red LED light stops flashing, then release it.
(Note – if the light continues flashing after being powered off
the battery is low and needs to be charged)
3. To play or pause a song: quickly press and release the button.
4. To answer or end a phone call or reject an incoming call:
quickly press the button when the phone starts ringing.
5. To re-dial the last called number: quickly press the button twice
" + " (Button #1)
1. To skip to the next song: press quickly and then release
2. To turn the volume up: press and hold for 3 seconds, release
when you've reached the desired volume
"- " (Button #5)
1. To skip to the previous song: press quickly and then release
2. To turn the volume down: press and hold for 3 seconds,
release when you've reached the desired volume
LED Indicator (#3):
The blue and red light alternately flashing when turning the
earphones on and off.
When trying to pair, the light flash blue.
When you receive an incoming call the light will flash blue.
When the earphones are being charged the red light will stay solid.
When fully charged the blue light will turn off.
Pairing The Bluetooth Earphones:
In order to use the earphones they must be paired with a
compatible Bluetooth device before you will be able to receive
calls or listen to music on it. ("Pairing" means to establish a
connection between Bluetooth devices. This makes compatible
devices store the unique ID of the earphones at the same time).
1. Put the earphones and compatible Bluetooth device close to
each other (no more than 3 feet apart) and press then hold the
"on/off" button until the LED light starts flashing blue. This tells
you that the earphones are ready for pairing.
2
2. With your Bluetooth compatible device turned on, enable the
scanning function to instruct the device to search for available
connections (for directions on how to do this, please refer to the
instruction manual for your Bluetooth device). When this is
complete, you should see a list of all available Bluetooth devices
within range.
3. Select "EH204" from the list, this should begin the pairing
sequence. After pairing has been successfully completed, you
will hear a quick tone in the earphones indicating that the
connection has been established.
4. Now you can use your Bluetooth earphones to take incoming
calls and listen to music.
Making And Receiving calls:
1. If the earphones are in use (ie. playing music) and you receive
an is an incoming call , the music will be paused and
automatically switched to "wait mode" while you take that call.
The music will resume automatically when the call is over.
2. When you hear an incoming call, press the "on/off" button once
to answer and then once again to finish the call (if the call is ended
by the other side you will not need to press the button again the
call will end automatically).
3.To redial the last number called, press the "on/off" button twice
quickly in succession.
Connection & Standby:
When the Bluetooth earphones are turned on, they will connect
automatically to the last connected compatible device within
range and then it will automatically enter standby mode.
Charging The Battery:
1. Fully charge the earphones before the using them for the first time.
2. Plug the provided USB charging cable into the appropriate
socket on the earphone and the other end into your USB device.
3. The light will begin flashing to indicate that the earphones are
being charged. The light will turn off after the earphones are
fully charged.
Attention: Please use the original included charging cable to
connect the earphones to your computer or compatible USB
charging device.
3