Silca Air4 V Serie Manual De Instrucciones página 5

Air
4
ATTENTION: before copying make sure the original remote control is working properly.Check the
state of the ba ery.
COPY FIXED CODES :
1.
Press and hold down bu on 1 on the "Air4 V-Air4 Plus V (EU&IB)" remote control and at
the same me press bu on 4 four mes.
(EU&IB)"remote control LED will fl ash briefl y about every 2 sec.
to be cloned in front of the "Air4 V-Air4 Plus V (EU&IB)", at a distance of about 2 cen metres.
4.
Press and hold down the bu on to be copied from the original remote control and wait for
the "Air4 V-Air4 Plus V (EU&IB)"LED to start fl ashing rapidly, which confi rms that the code has
been acquired. This opera on may take a few seconds.
"Air4 V-Air4 Plus V (EU&IB)"bu on to which the code must be transferred and hold down un l
the LED goes out.
N.B. •If the LED goes out unexpectedly it means the code has not been acquired. Repeat the
opera on from point 1.• To programme the second "Air4 V-Air4 Plus V (EU&IB)"bu on, repeat
the opera on from point 1.
COPY ROLLING CODE NORMAL* :Follow the "Fixed Code" instruc ons.
COPY ROLLING SECURE LEARNING* :
1.
Press and hold down bu on 1 on the "Air4 V-Air4 Plus V (EU&IB)"and at the same me press
bu on 4 four mes. 2. Release both bu ons: the "Air4 V-Air4 Plus V (EU&IB)"LED will fl ash
briefl y about every 2 sec. 3. Place the remote control to be cloned in front of the "Air4 V-Air4
Plus V (EU&IB)", at a distance of about 2 cen metres. 4. Press and hold down the bu on to be
copied from the original remote control and wait for the "Air4 V-Air4 Plus V (EU&IB)"LED to go
on without fl ashing and then start double fl ashing about every 2 seconds.
nal remote control source code (check the website www.silca.biz to fi nd the one for the remote
control you want to copy).
bu on by which the code will be memorised and hold down un l the LED goes out.
(*) Full list of original models at: www.silca.biz.
N.B.: Transmit the source code to copy an "Air4 V-Air4 Plus V (EU&IB)"remote control program-
med as "Rolling Secure Learning".
PROCEDURE A.L.S.:Simplifi ed procedure to ac vate the remote control on the receiver. The list
of receivers compa ble with the procedure can be found on www.silca.biz. For other receivers
see the original instruc ons provided by the manufacturer.
N.B.:Follow A.L.S. procedure before using the original remote control.
1.Stand close to the automa on 2.Hold down the programme bu on for about 10 seconds;
release when the LED starts to fl ash 3.Wait un l the LED goes out.
ATTENTION : receivers may have the radio channel disabled. In such cases enter the new re-
mote controls using a manual procedure.
TRANSMISSION OF "Air4 V-Air4 Plus V (EU&IB)" SOURCE CODE :
1.Press bu ons 1 and 2 on the remote control simultaneously for 8 seconds and release when
the LED fl ashes.2.While the LED is fl ashing press the bu on for which the source code is requi-
red.
Ba ery replacement:
(EU&IB)"remote control.The "Air4 V-Air4 Plus V (EU&IB)"remote control is powered by a 3V CR2032 LITHIUM
BATTERY. Check polarity-Do not throw fl at ba eries away: dispose of them in the special waste sor ng centres.
6.
The "Air4 V-Air4 Plus V (EU&IB)"LED will fl ash rapidly; press the
Use a star screwdriver to loosen the screw on the back of the "Air4 V-Air4 Plus V
Copyright Silca S.p.A 2018
2. Release both bu ons: the "Air4 V-Air4 Plus V
5.
While the LED is fl ashing, press the
English
3.
Place the remote control
5.
Transmit the origi-
ENGLISH
5