Descargar Imprimir esta página

Monster MST707 Manual Del Propietário página 2

Publicidad

Idiomas disponibles

Idiomas disponibles

FAILURE TO OBSERVE THESE WARNINGS COULD RE SULT IN IN JU RY.
THIS INSTRUCTION MANUAL CONTAINS IMPORTANT SAFETY
INFORMATION.
READ THIS INSTRUCTION MANUAL CAREFULLY AND
UNDERSTAND ALL INFORMATION BEFORE OPERATING THIS
TOOL.
• Read and understand all instructions. Failure to follow
all instructions listed below, may result in electric
shock, fire, explosion and/or serious personal injury. It is
the responsibility of the owner to make sure all personnel
read this manual prior to using the device. It is also
the responsibility of the device owner to keep this
manual intact and in a convenient location for all to
see and read. If the manual or product labels are lost
or not legible, contact Monster Mobile for replacements.
If the operator is not fluent in English, the product
and safety instructions shall be read and discussed
with the operator in the operator's native language by
the purchaser/owner or his designee, making sure that
the operator comprehends its contents.
• Always operate, inspect and maintain this tool in
accordance with American National Standards Institute
Safety Code of Portable Air Tools (ANSI B186.1) and any
other applicable safety codes and regulations.
• For safety, top performance and maximum durability of
parts, operate this tool at 90 psig; 6.2 bar max air
pressure with 3/8" diameter air supply hose.
• Always wear impact-resistant eye protection and face
protection when operating or performing maintenance on
this tool (users and bystanders).
• High sound levels can cause permanent hearing loss.
Always use hearing protection as recommended by your
employer an OSHA regulations while using this tool
(users and bystanders).
• Keep the tool in efficient operating condition.
• Operators
physically able to handle the bulk, weight and power of
this tool.
• Operation can cause impacts, cuts, abrasions and heat. Wear
gloves to protect hands.
• Air under pressure can cause severe injury. Never direct
air at yourself or others. Always turn off the air supply,
drain hose of air pressure and detach tool from air supply
before installing, removing or adjusting any accessory
on this tool, or before performing any maintenance on
this tool. Failure to do so could result in injury. Whip
hoses can cause serious injury. Always check for
damaged, frayed or loose hoses and fittings, and replace
immediately. Do not use quick detach couplings at tool.
See instructions for correct set-up.
• Keep tool out of reach of children.
• Air powered tools can vibrate in use. Vibration, repetitive
motions or uncomfortable positions over extended
periods of time may be harmful to your hands and arms.
Discontinue use of tool if discomfort, tingling feeling or
pain occurs. Seek medical advice before resuming use.
• Slipping, tripping and/or falling while operating air
tools can be a major cause of serious injury or
death. Be aware of excess hose left on the walking
or work surface.
MST707
and
maintenance
personnel
WARNING
• Keep body working stance balanced and firm. Do
• Note direction of rotation BEFORE operating this tool.
• Anticipate and be alert for sudden changes in motion
• Do not carry tool by the hose. Protect the hose from
• Tool shaft may continue to rotate briefly after throttle is
• Keep away from rotating end of tool. Do not wear
• Do not use (or modify) the tool for any other purpose
• Correct cut-off wheel mounting is necessary to prevent
• When using the cut-off tool, be careful not to exert excessive
RPM
RPM
RPM
must
be
• Never operate this tool without required disc cover/
• RPM OF THE ACCESSORY MUST EXCEED TOOL RPM. Use
• Use replacement parts and accessories recommended by
• Do not lock, tape or wire the "on/off" safety lever in the
• Do not lu bri cate tools with flam ma ble or vol a tile liq uids
• This tool is not insulated against electric shock.
• This tool must not be used in explosive atmospheres.
• Servicing and repairs should only be made by an
• Do not force tool beyond its rated capacity.
• Do not remove any labels. Replace damaged labels.
• Failure to heed these warnings may result in serious or
2
not overreach when operating the tool.
during start up and operation of any power tool.
sharp objects and heat.
released. Avoid direct contact with accessories during
and after use. Gloves will reduce the risk of cuts or
burns.
jewelry or loose clothing. Secure long hair. Scalping
can occur if hair is not kept away from tool and
accessories. Choking can occur if neckwear is not
kept away from tool and accessories.
than that for which it was designed without consulting
the manufacturer's authorized representative.
injury from broken wheels. Do not use chipped or cracked
cut-off wheels. Cut-off wheels should be a free fit on the
spindle to prevent stress at the hole. Use only wheel collars
that come with the tool for mounting the cut-off wheel. Flat
washers or other adapters may over stress the wheel.
Tighten the wheel on the spindle to prevent spin off when the
tool is turned off.
force. Too much force could be hazardous if it causes the
tool spindle to bend or break. The burning of the work piece
or excessive speed reduction indicates too much force being
applied. Start the tool off the work, set it down on the work
evenly and move in the direction desired to make the cut.
When finished cutting, lift off the work before stopping the
motor.
guard in place.
accessories rated at 15,000 RPM or higher.
Monster Mobile.
"on"position, as the lever must be free to return to the
"off" position when released.
such as ker o sene, die sel or jet fuel.
authorized service center.
fatal personal injury and/or property damage.
04/30/18

Publicidad

loading