Sunex Tools SX231B Instrucciones De Operación página 4

Operating Instructions • Warning Information • Parts Break down
Whip Hose
Do Not Install
Quick Coupling Nipple
Here
Leader Quick Coupler
Hose
fig. 1.
AIR SUPPLY
Tools operate on a wide range of air pressures. It is
recommended that air pressure measures 90 psig at the
tool with the trigger fully depressed and no load applied
to the tool. Higher pressure (over 90 psig; 6.2 bar) raises
performance beyond the rated capacity of the tool, which
will shorten tool life and could cause injury.
Always use clean, dry air. Dust, corrosive fumes and/
or water in the air line will cause damage to the tool.
Drain the water from air lines and compressor prior to
running tool. Clean the air inlet filter screen weekly.
The recommended hookup procedure can be viewed
in FIG. 1.
The air inlet used for connecting air supply has
standard 1/4" NPT. Line pressure should be increased to
compensate for unusually long air hoses (over 25 feet).
Minimum hose diameter should be 3/8" I.D. and fittings
should have the same inside dimensions and be tightly
secured.
Ensure an accessible emergency shut off valve has
been installed in the air supply line and make others
aware of its location.
TROUBLESHOOTING
Other factors outside the tool may cause loss of power
or erratic action. Reduced compressor output, excessive
drain on the air line, moisture or restrictions in air pipes
or the use of hose connections of improper size or poor
conditions may reduce air supply. Grit or gum deposits
in the tool may cut power and may be corrected by
cleaning the air strainer and flushing out the tool with
gum solvent oil or an equal mixture of SAE #10 and
kerosene. If outside conditions are in order, disconnect
tool from hose and take tool to your nearest authorized
service center.
LUBRICATION AND MAINTENANCE
Lubricate the air motor daily with high quality air tool oil.
If no air line oiler is used, run 1/2 oz. of oil through the
tool. The oil can be squirted into the tool air inlet or into
the hose at the nearest connection to the air supply, then
run the tool. A rust inhibitive oil is acceptable for air tools.
WARNING: After an air tool has been lubricated, oil will
discharge through the exhaust port during the first
few seconds of operation. The exhaust port must be
covered with a towel before applying air pressure to
prevent serious injury.
OPERATION
Always turn off the air supply, drain hose of air
pressure and detach tool from air supply before
SX231B: Parts Breakdown & Operating Manual
Air Supply
Filter
Nipple
Oiler Regulator
Drain Daily
installing, removing or adjusting any part or accessory
on this tool, or before performing any maintenance on
this tool.
Bonded abrasive mounted point grinding wheels, rotary
files and carbide burrs can be mounted providing their
speed rating exceeds the speed of the Die Grinder. The
shank size of the mounted accessory must match the
collet size fitted in the Die Grinder. Insert the shank of
the mounted point as far as possible into the collet and
tighten the nut using the supplied wrenches. Minimum
shank gripping length must be 10mm.
After mounting a new point, start the Die Grinder under
bench and run for a few seconds. If the Die Grinder starts
to vibrate when first fitting a mounted point or during
operation, immediately remove from service. If Die
Grinder is dropped, replace bonded abrasive mounted
point grinding wheel, rotary file or carbide burr.
When using the Die Grinder, be careful not to exert
excessive force which could be hazardous and cause
mounted spindle to bend or break.
NOTE: During operation, safety goggles should always
be worn to guard against flying debris (users and
bystanders).
WARNING: Never mount a grinding wheel, cut-off
wheel, router cutter or drill bit on a Die Grinder. Never
use an arbor, mandrel or any other adapter to convert
the Die Grinder for any other application.
For a complete listing of Authorized Master Repair
Centers, visit www. sunextools.com.
LIMITED WARRANTY
SUNEX INTERNATIONAL, INC. WARRANTS TO ITS
CUSTOMERS THAT THE COMPANY'S SUNEX TOOLS ®
BRANDED PRODUCTS ARE FREE FROM DEFECTS IN
WORKMANSHIP AND MATERIALS.
Sunex International, Inc. will repair or replace its Sunex Tools ® branded
products which fail to give satisfactory service due to defective workmanship
or materials, based upon the terms and conditions of the following described
warranty plans attributed to that specific product. This product carries a
ONE-YEAR warranty. During this warranty period, Sunex Tools ® will repair or
replace at our option any part or unit which proves to be defective in
material or workmanship.
Other important warranty information...
This warranty does not cover damage to equipment or tools arising from
alteration, abuse, misuse, damage and does not cover any repairs or
replacement made by anyone other than Sunex Tools ® or its authorized
warranty service centers. The foregoing obligation is Sunex Tools ® sole
liability under this or any implied warranty and under no circumstances shall
we be liable for any incidental or consequential damages.
Note: Some states do not allow the exclusion or limitation of incidental or
consequential damages, so the above limitation or exclusion may not apply
to you. Return equipment or parts to Sunex Tools ® , or an authorized
warranty service center, transportation prepaid. Be certain to include your
name and address, evidence of the purchase date, and description of the
suspected defect.
If you have any questions about warranty service, please write to Sunex
Tools ® . This warranty gives you specific legal rights and you may also have
other rights which vary from state to state. Repair kits and replacement
parts are available for many of Sunex Tools ® products regardless of whether
or not the product is still covered by a warranty plan.
SHIPPING ADDRESS:
Sunex Tools • 315 Hawkins Rd. • Travelers Rest, SC 29690
MAILING ADDRESS:
Sunex Tools • P.O. Box 1233 • Travelers Rest, SC 29690
4 Rev. 3/11/20