Sunex Tools SXC202 Instrucciones Operativas página 4

Operating Instructions • Warning Information • Parts Breakdown
Air Supply...
Tools of this class operate on a wide range of air pressures.
It is recommended that air pressure of these tools measures
90 PSI at the tool while running free. Higher pressure (over
90 psig; 6.2 bar) raises performance beyond the rated
capacity of the tool, which will shorten tool life because of
faster wear and could cause injury.
Always use clean, dry air. Dust, corrosive fumes and/or
water in the air line will cause damage to the tool. Drain the
air tank daily. Clean the air inlet filter screen on at least a
weekly schedule. The recommended hookup procedure can
be viewed in the above figure.
The air inlet used for connecting air supply has standard
1/4" NPT. Line pressure should be increased to compensate
for unusually long air hoses (over 25 feet). Minimum hose
diameter should be 3/8" I.D. and fittings should have the
same inside dimensions and be tightly secured.
Limited Warranty...
SUNEX INTERNATIONAL, INC. WARRANTS TO ITS CUSTOMERS THAT THE COMPANY'S SUNEX TOOLS ®
BRANDED PRODUCTS ARE FREE FROM DEFECTS IN WORKMANSHIP AND MATERIALS.
Sunex International, Inc. will replace any SXC Series Air Tool which fails to give satisfactory service due to defective workmanship
or materials. This product carries a ONE-YEAR warranty. During this warranty period, Sunex Tools will replace free of charge
any part or unit which proves to be defective in material or workmanship.
Other important warranty information...
This warranty does not cover damage to equipment or tools arising from alteration, abuse, misuse, damage and does not cover
any repairs or replacement made by anyone other than Sunex Tools or its authorized warranty service centers.The foregoing
obligation is Sunex Tools' sole liability under this or any implied warranty and under no circumstances shall we be liable for any
incidental or consequential damages.
Note: Some states do not allow the exclusion or limitation of incidental or consequential damages, so
the above limitation or exclusion may not apply to you. Return tool to Sunex Tools, transportation prepaid. Be
certain to include your name and address, evidence of the purchase date, and description of the suspected defect.
If you have any questions about warranty service, please write to Sunex Tools. This warranty gives you specific legal rights and
you may also have other rights which vary from state to state. After the one year direct replacement warranty has expired, some
service parts are available for purchase through normal Sunex Tools service options.
Shipping Address: Sunex Tools • 315 Hawkins Rd. • Travelers Rest, SC 29690
Mailing Address: Sunex Tools • P.O. Box 4215 • Greenville, SC 29608
SXC202
Operation...
When using the grinder, be careful not to exert excessive
force. Too much force may be hazardous if it causes the
cutting tool spindle to bend or break.
The burning of the work piece or excessive speed reduction
indicates too much force being applied. Changing to a free
cutting tool may be better for the desired rate of speed and
stock removal.
Avoid hazardous condition by making sure there is sufficient
gripping force on the spindle of the cutting tool by placing
the spindle 7/16" or more inside the collet.
Lubrication...
Lubricate the air motor daily with quality air tool oil. If no
air line oiler is used, run a teaspoon of oil through the tool.
The oil can be squirted into the tool air inlet or into the hose
at the nearest connection to the air supply, then run the tool.
The amount of oil to be used is 1 ounce. Overfilling will
cause a reduction in the power of the tool.
Other factors outside the tool may cause loss of power or
erratic action. Reduced compressor output, excessive drain
on the air line, moisture or restrictions in air pipes or the
use of hose connections of improper size or poor condition
may reduce air supply. Grit or gum deposits in the tool may
cut power and may be corrected by cleaning the air strainer
and flushing out the tool with gum solvent oil or an equal
mixture of SAE #10 oil and kerosene.
4 Rev. 01/11/05