Tabla de contenido
Publicidad
Enlaces rápidos
© 2009-2010, Moog Videolarm, Inc. All Rights Reserved
F D W 7 5 C 1 2 N
Fusion Dome (Outdoor Wall Mount with Housing)
Installation and Operation Instructions for the following models:
FDW75C12N
IP Network Ready 7" Outdoor dome hsg w/wall mount, clear dome, with
12VDC input, heater/blower, fan an IP Network PTZ camera.
FDP75C12N
IP Network Ready 7" Outdoor dome hsg w/pendant mount, clear dome, with
12VDC input, heater/blower, fan an IP Network PTZ camera.
Before attempting to connect or operate this product,
please read these instructions completely.
www.videolarm.com
CERTIFIED
81-IN5329
08-16-2010
Publicidad
Tabla de contenido
Manuales relacionados para Moog Videolarm FDW75C12N
Resumen de contenidos para Moog Videolarm FDW75C12N
- Página 1 © 2009-2010, Moog Videolarm, Inc. All Rights Reserved F D W 7 5 C 1 2 N Fusion Dome (Outdoor Wall Mount with Housing) www.videolarm.com Installation and Operation Instructions for the following models: FDW75C12N IP Network Ready 7” Outdoor dome hsg w/wall mount, clear dome, with 12VDC input, heater/blower, fan an IP Network PTZ camera.
-
Página 2: Important Safeguards
IMPORTANT SAFEGUARDS SAFETY PRECAUTIONS Read these instructions. Keep these instructions. CAUTION Heed all warnings RISK OF ELECTRIC SHOCK DO NOT OPEN Follow all instructions. Do not use this apparatus near water. CAUTION: TO REDUCE THE RISK OF Clean only with damp cloth. ELECTRIC SHOCK, DO NOT REMOVE Do not block any of the ventilation openings. -
Página 3: Disclaimerof Warranty
LIMITED WARRANTY FOR VIDEOLARM INC. PRODUCTS VIDEOLARM INC. warrants this Product to be free from defects in material or workmanship,as follows: PRODUCTCATEGORY PARTS LABOR All Enclosures and Electronics Five (5) Years Five (5) Years Pan/Tilts Three (3) Years **6 months if used in autoscan Three (3) Years **6 months if used in autoscan /tour operation /tour operation... -
Página 4: Electrical Specifications
Contents of Box Electrical Specifications FDW75C12N Power 12VDC Class 2 Only 24 VAC 21 Watts Accessories: Heater: 20 Watts, Blower: 1 Watt Camera Power: 40 Watts Max Tools Required: .100” Flat Head Screwdriver Phillips Head Screwdriver English 24 VAC 21 vatios... -
Página 5: Wall Mounting
WALL MOUNTING 4”-5” Trim incoming control & power wires to 4”- 5”, Bracket is designed for 45° conduit fitting (If using the conduit). Run wire into bracket secure to wall. for either wall or pendent bracket • El soporte se diseña para la guarnición del conducto 45° (si usa el •... - Página 6 Important Gasket Must be in place Align large arrows To lock turn clockwise • Con seguridad soporte del montaje a emparedar. Tire del cableado • Con seguridad soporte del montaje a emparedar. Tire del cableado a través del soporte y del ojal de la posición según lo demostrado. a través del soporte y del ojal de la posición según lo demostrado.
- Página 7 Complete all wiring connections Secure lanyard to lanyard clip (coax wire not supplied) • Termine todas las conexiones del cableado • Con seguridad soporte del montaje a emparedar. Tire del cableado a través del soporte y del ojal de la posición según lo demostrado. (alambre coaxil no suministrado) •...
- Página 8 To loosen - unscrew bolts ½” turn counter Secure with ¼” Allen wrench clockwise • Asegure con la llave Allen del ¼” • Para aflojar - desatornille a la derecha contrario de la vuelta del ½ de los pernos” • Fixez clé Allen avec de ¼” •...
- Página 9 RJ45 24VAC POWER Camera + 12VDC Max 40 Watts Camera - 12VDC Orange Heater/Blower + 12VDC Yellow 21 Watts Heater/Blower - 12VDC Green BNC (Not supplied) Make the appropriate male and female connections. Indoor model does not include pre-run cables. •...
- Página 10 Axis 213 (3) #8x3/8” Captive Screw Mounting Plate 1" 2" MOUNTING HOLE MOUNTING HOLE Install the camera to the mounting plate with (2) #10 screws and lock washers provided. Place (3) #8x3/8” screws on the spacers and align the mounting slots. Slide on plate and camera then secure. •...
- Página 11 Axis 215 (3) #8x3/8” Mounting Plate ½" 1" 2" MOUNTING HOLE MOUNTING HOLE Install the camera to the mounting plate using (4) #8 bolts and star washers. Place (3) #8x3/8” screws on the spacers and line up the mounting slots. Slide plate in and secure. •...
- Página 12 CANON - VB-C10 Captive Screw Mounting Plate (3) #8x3/8” 1" 2" MOUNTING HOLE MOUNTING HOLE Install the camera to the mounting plate with (2) #10 screws and lock washers provided. Place (3) #8x3/8” screws on the spacers and align the mounting slots. Slide on plate and camera then secure. •...
- Página 13 ELMO 400/401 Captive (4) #8x3/8” Screw Mounting Plate ½" 1" 2" MOUNTING HOLE MOUNTING HOLE Attach camera to mounting plate using (4) #8 screws, star washer, and nuts. Complete assembly as shown, then secure camera and mounting plate to spacers. •...
- Página 14 JVC-VN625U Captive (4) #8x3/8” Screw Mounting Plate 1" MOUNTING HOLE Attach quick release bracket to mounting plate using (4) #8 screws and star washer. Complete assembly as shown, then secure camera to the quick release plate. • Una el soporte rápido del lanzamiento a la placa de montaje usando (4) los tornillos #8 y la arandela de la estrella. Termine a asamblea como cámara fotográfica demostrada, después segura a la placa rápida del lanzamiento.
- Página 15 Panasonic KX-HCM180 Captive (3) #8x3/8” Screw Mounting Plate 1" 2" MOUNTING HOLE Attach camera to mounting plate using (1) ¼” x 20 bolt, lock washer, and washer. Complete assembly as shown, then secure camera to the quick release plate. • Ate la cámara a la pletina usando (1) perno de x 20 del ¼”, arandela de cerradura, y arandela. Termine a la asamblea como se muestra, entonces cámara segura a la placa del lanzamiento rápido.
- Página 16 Panasonic WV-NS954 (4) #8x3/8” Mounting Plate ½" MOUNTING HOLE Attach bracket to (4) spacers using (4) #8 screws and star washer. Complete assembly as shown, then secure camera to the quick release plate. • Ate el soporte (4) a los espaciadores usando (4) los tornillos #8 y arandela de la estrella. Termine a la asamblea como se muestra, entonces cámara segura a la placa del lanzamiento rápido.
- Página 17 RZ25 Captive (3) #8x3/8” Screw Mounting Plate ½" MOUNTING HOLE Attach camera to mounting plate using (1) ¼” x 20 bolt, washer, lockwasher, (2) M3 x 8mm bolts, and lockwashers. Complete assembly as shown, then secure camera to the quick release plate. •...
- Página 18 RZ50 Captive (3) #8x3/8” Screw Mounting Plate 2" MOUNTING HOLE Attach camera to mounting plate using (1) ¼” x 20 bolt, washer, lock washer, and (2) M3 bolts and washers. Complete assembly as shown, then secure camera to the quick release plate. •...
- Página 19 Pixord 261/263 Captive (3) #8x3/8” Screw Mounting Plate 1" MOUNTING HOLE Attach camera quick release bracket to mounting plate using (3) 8 x 32 x ⅜” bolts, lock washers, and nuts. Complete assembly as shown. • Ate el soporte del lanzamiento rápido de la cámara a la pletina usando (3) pernos del ⅜ de 8 x 32 x los”, las arandelas de cerradura, y las tuercas. Termine a la asamblea como se muestra.
- Página 20 Fasten down the dome with a Phillips Wipe the dome clean. screwdriver. • Sujete abajo de la bóveda con un destornillador • Limpie la bóveda limpia. Phillips. • Attachez en bas du dôme avec un tournevis • Essuyez le dôme. Phillips.
-
Página 21: Replacement Parts List
Replacement Parts List FDW75C12N PART NUMBER DESCRIPTION FD7C CLEAR REPLACEMENT CAPSULE 1A FD7T TINTED REPLACEMENT CAPSULE RPFD7501 LOWER TRIM RING RPFD703 DOME CLAMPING RING RPNET02 NETWORK HGS POWER SUPPLY RPFD072 24V HEATER 5A RPFD072/12 12V HEATER (12VDC MODELS ONLY) RPFD080... -
Página 22: Product Registration/Warranty
Product Registration/Warranty Thank you for choosing Videolarm. We value your patronage and are solely committed to providing you with only the highest quality products available with unmatched customer service levels that are second-to-none in the security industry. Should a problem arise, rest assure that Videolarm stands behind its products by offering some of the most impressive warranty plans available: 3 Years on all Housings, Poles, Power Supplies, and Accessories and 5 Years on all camera systems (SView, QView, Warriors), and InfraRed Illuminators.