Publicidad
Idiomas disponibles
Idiomas disponibles
Operating Instructions • Warning Information • Parts Breakdown
Maximum Service Pressure . . . . . . . . . . 140 PSIG (9 .7 bar)
Maximum Air Flow . . . . . . . . . . . . . . . . . . . . . . 575 SCFM
Oil Capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 .4 fl . oz .
AlwAys reAd
instructions
before using
power tools
AlwAys weAr
sAfety goggles
weAr heAring
protection
Avoid
prolonged
exposure to
vibrAtion
AL21
REGULATOR UNIT
S P E C I F I C A T I O N S
some dust created by power sanding, sawing, grinding, drilling, and other construction
activities contains chemicals known to cause cancer, birth defects or other reproductive
harm. some examples of these chemicals are:
• lead from lead-based paints,
• crystalline silica from bricks and cement and other masonry products, and
• arsenic and chromium from chemically-treated lumber.
your risk from these exposures varies, depending on how often you do this type of
work. to reduce your exposure to these chemicals: work in a well ventilated area, and
work with approved safety equipment, such as those dust masks that are specially
designed to filter out microscopic particles.
Operating Temperature Range . . . . . . . . 41 - 140ºF (5-60ºC)
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 .25 lbs .
Dimensions . . . . . . . . . . . . . . . . W 3 .13" x H 7 .0" x D 2 .4"
Copyright © Professional Tool Products, 2012
1
AL21
AL21
All rights reserved.
05/15/12
Publicidad
Tabla de contenido
Resumen de contenidos para Matco Tools AL21
- Página 1 AL21 REGULATOR UNIT Operating Instructions • Warning Information • Parts Breakdown S P E C I F I C A T I O N S AL21 Maximum Service Pressure . . . . . . . . . . 140 PSIG (9 .7 bar) Operating Temperature Range .
- Página 2 AL21 REGULATOR UNIT WARNING fAiLure To oBserVe These WArnings couLd resuLT in inJury • Keep body working stance balanced and firm. Do This insTrucTion MAnuAL conTAins not overreach when operating the tool. iMporTAnT sAfeTy inforMATion. • Anticipate and be alert for sudden changes in motion reAd This insTrucTion MAnuAL cArefuLLy during start up and operation of any power tool.
- Página 3 AL21 REGULATOR UNIT Be certain to include your name and address, evidence of the insTALLATion of reguLATor purchase date, and description of the suspected defect. 1. Maximum air pressure to unit is 140 PSIG (9.7 BAR). If you have any questions about warranty service, please write 2. Mount the unit as close to the item to be protected as possible. to Matco Tools, Stow, OH 44224. This warranty gives you specific 3. Direction of air flow is designated by an " " and " " on the legal rights and you may also have other rights which vary from primary unit. state to state. 4. Install Dial Gauge (#19) by screwing brass fitting on back of Gauge clockwise into the threaded hole provided in front of the primary unit, just above the regulator adjustment knob (#10).
- Página 4 AL21 REGULATOR UNIT ITEM PART NO. DESCRIPTION QTY. Body Dome O-Ring Piston O-Ring V-Ring Spring Adjusting Screw Nut 10 Knob 11 Valve 12 O-Ring 13 O-Ring 14 Spring 15 O-Ring 16 Cap 17 Bracket 18 Fixed Ring 19 RSAL2119 Gauge 20 Nut 21...
-
Página 5: Unidad De Regulador
AL21 UNIDAD DE REGULADOR instrucciones de operación • Inforación de Advertencia • Revisión de Refacciones E S P E C I F I C A C I O N E S AL21 Máxima presión de servicio . . . . . . . . . . 140 PSIG (9 .7 bar) Rango de temperatura de operación . -
Página 6: Al21 Unidad De Regulador
AL21 UNIDAD DE REGULADOR ADVERTENCIA EL INCUMPLIMIENTO DE OBSERVAR ESTAS ADVERTENCIAS PUEDEN RESULTAR EN ALGUNA LESIÓN • Mantenga balanceada y firme la postura corporal de esTe MAnuAL insTrucciones trabajo. No se extra limite al operar esta herramienta. conTiene inforMAciÓn iMporTAnTe de seguridAd. LeA cuidAdosAMenTe esTe • Anticipe y sea alerto por cambios repentinos de MAnuAL insTrucTiVo y coMprendA TodA movimiento durante el arranque inicial y operación de... -
Página 7: Instalación Del Regulador
AL21 UNIDAD DE REGULADOR Tools bajo ésta o cualquier otra garantía limitada y no seremos insTALAciÓn deL reguLAdor responsables bajo ninguna circunstancia por ningún daño 1. La máxima presión de aire a la unidad es de 140 PSIG (9.7 BARRAS). incidental ni consecuencial. 2. Monte la unidad lo más cercano posible al artículo a NOTA: Algunos estados no permiten la exclusión ni limitación...