Milwaukee M12 202B Serie Manual Del Operador página 3

SPECIFICATIONS
Cat. No. ........................202B Series, 202G Series
Volts.............................................................. 12 DC
Battery Type .................................................M12™
Charger Type................................................M12™
FUNCTIONAL DESCRIPTION
2
3
1. Jacket and Pocket
High: Red LED
Medium: White LED
Low: Blue LED
2. Battery Controller Pocket
3. Power Cable
ASSEMBLY
Recharge only with the charger
WARNING
specified for the battery. For spe-
cific charging instructions, read the operator's
manual supplied with your charger and battery.
Inserting/Removing the Battery
To insert the battery, slide the pack into the body of
the battery controller. Make sure it latches securely
into place.
Insert the power cable (from inside the battery
controller pocket) into the power cable port on the
battery controller.
Place the battery controller into the pocket and zip
closed. If necessary, unzip the expansion zipper to
accommodate larger battery packs.
To remove the battery, push in the release buttons
and pull the battery pack away from the controller.
OPERATION
The zone power buttons are located on the upper left
side of the jacket. Use the jacket
power buttons to control the two zones.
To turn on, press and hold (1 to 2 seconds) the
zone's power button. The zone will be turned to High
and the red LED will light.
Temperature setting can be adjusted at any time
by pressing the zone's power button. Each press
will cycle through the zone's temperature settings.
To turn off the heated jacket, press and hold (1 to 2 sec-
onds) the zone's power button. The LED will turn off.
If the heated jacket turns off unexpectedly, check
connections and charge the battery pack.
202R Series, 222C Series
Power Buttons
and pocket
To reduce the risk of injury, always
WARNING
unplug the charger and remove the
battery pack and battery controller from the
heated jacket before performing any mainte-
nance. Never disassemble the heated jacket,
battery pack or charger. Contact a MILWAUKEE
service facility for ALL repairs.
If the heated jacket does not start or operate properly
with a fully charged battery pack, clean the contacts
on the battery pack. If the heated jacket still does
not work properly, return the heated jacket, charger
and battery pack, to a MILWAUKEE service facility
1
for repairs.
To reduce the risk of personal in-
WARNING
jury and damage, disconnect and
remove battery pack and battery controller from
battery controller pocket before washing. Never
immerse your battery controller, battery pack, or
charger in liquid or allow a liquid to flow inside
them.
To clean the heated jacket:
1. Remove battery pack and battery holder.
2. Push the power cord completely into the battery
holder pocket and fasten closed.
3. Machine wash, Gentle Cycle in warm water. Do not
use bleach. Do not dry clean. Do not wring or twist.
4. Tumble Dry on Low Heat. Do not iron.
ACCESSORIES
Use only recommended accesso-
WARNING
ries. Others may be hazardous.
For a complete listing of accessories, go online to
www.milwaukeetool.com or contact a distributor.
SERVICE - UNITED STATES
1-800-SAWDUST
Monday-Friday, 7:00 AM - 6:30 PM CST
www.milwaukeetool.com
or visit
Contact Corporate After Sales Service Technical
Support with technical, service/repair, or warranty
questions.
Email: metproductsupport@milwaukeetool.com
B e c o m e a H e a v y D u t y C l u b M e m b e r a t
www.milwaukeetool.com to receive important
notifications regarding your tool purchases.
SERVICE - CANADA
Milwaukee Tool (Canada) Ltd
1.800.268.4015
Monday-Friday, 7:00 AM - 4:30 PM CST
or visit www.milwaukeetool.ca
LIMITED WARRANTY
USA & CANADA
Every MILWAUKEE M12 HEATED JACKET (including its battery holder) is
warranted to the original purchaser only to be free from defects in material
and workmanship. Subject to certain exceptions, MILWAUKEE will repair
or replace any part on M12™ Heated Jacket which, after examination, is
determined by MILWAUKEE to be defective in material or workmanship
for a period of one (1) year* after the date of purchase. Return of the
Heated Jacket to a MILWAUKEE factory Service Center location, freight
prepaid and insured, is required. A copy of the proof of purchase should
be included with the return product. This warranty does not apply to dam-
age that MILWAUKEE determines to be from repairs made or attempted
by anyone other than MILWAUKEE personnel, misuse, alterations, abuse,
normal wear and tear, or accidents.
*This warranty does not cover a M12™ LITHIUM-ION Battery Pack; there
is a separate and distinct warranty available for a battery pack.
3
CARE
(1.800.729.3878)