Maintenance And Cleaning - Nahita 631 Plus Serie Manual De Instrucciones

When you are not using the equipment for a long period of time please make sure it is
unplugged from the net in order to avoid possible accidents.
It is essential to have the equipment switched off and unplugged from the net before
cleaning, checking components or replacing any piece (e.g. replacement of a fuse).
Never try to repair the equipment by yourself, since you will lose the warranty and may
provoke damages to the general operating system or the electrical installation, as well as
injuries to the people that usually handle the equipment (burns, hurts...).
Try not to spill any liquid on the control panel, though it is properly insulated. In case
you have any doubts do please immediately unplug the equipment (see Maintenance).
Made under the European regulations for electrical security, electromagnetic compati-
bility and security on machines.

5. MAINTENANCE AND CLEANING

To get the best results and a higher duration of the equipment it is essential to follow
the processes of use.
Note: All the processes of use mentioned below will not have any value unless you keep
a continued and careful maintenance.
Please follow the processes of use of this manual.
This manual should be available for all users of this equipment.
Always use original components and supplies. Other devices can be similar but they
can damage the equipment.
Process with caution to avoid the damage of the cables or other components.
The equipment is supplied with a standard Schuko wire. It has to be plugged to an earth
connection and the socket should be handy and ready to unplug the equipment in case of
emergency.
Never try to repair the equipment by yourself, since you will lose the warranty and may
provoke damages to the general operating system or the electrical installation, as well as
injuries to the people that usually handle the equipment (burns, hurts...) or damages in
nearby equipments.
In the event of breakdown please contact your distributor to overhaul through Nahita
Technical Assistance Department.
Cleaning
Never use scourers or substances that can grate for cleaning metallic parts such as stain-
less steel, aluminium, coatings, etc. as they damage the incubator and produce an early
ageing of the equipment.
Use a fluff-free cloth dampened with soaped water that does not contain abrasives.
ATTENTION!! IF EQUIPMENTS ARE NOT PROPERLY CLEAN AND
DISINFECTED THEY WOULD NOT BE ALLOWED TO REPAIR BY OUR
TECHNICAL SERVICE.
Page 18 Instruction manual 5063xxx1
ENGLISH
Version 2 February 2015
4. INSTALLATION / SETTING UP
Preliminary inspection
Unwrap the equipment, take off the involving plastic and take off the polyspan protec-
tion in which it comes fitted.
Take off all the protective items and, without connecting the equipment to the net, make
sure that it does not present any damage because of the shipment. In case the equipment
presents any damage tell it immediately to your transport agent or dealer so that they can
make the claims in the correct time limit.
We will only accept the equipment return within 15 days after delivery provided it
comes in its original wrapping.
Please keep the original wrapping; you will always need it for returns enclosed with all
the accessories supplied.
Please check that all the accessories are enclosed with the equipment:
- 2 Trays and 4 guides
- Shuko wire
- User's manual
Installation
Before using this instrument, it is convenient for you to familiarize with its components
and basic essentials.
PLEASE READ THOROUGHLY THE INSTRUCTIONS BEFORE CONNECTING
AND OPERATING WITH THIS EQUIPMENT.
Put the equipment on top of a horizontal, plane and stable table making a free space
around so as the ventilation grilles are completely free of obstructions.
Do not put the equipment near any warm supply (burners, blowlamps...), nor expose
it directly to the sun, etc. Avoid the presence of flammable or toxic products in the wor-
king area.
Place the trays supplied with the equipment at the desired height.
The equipment is supplied with a Schuko standard wire. Please insert the wire that
feeds the AC electric current in the base of current 220 V, 50 Hz ±10% provided with earth
wire and the other end to the equipment connector (1.4). The tension should be 220 V, 50
Hz ± 10%.
Neither the manufacturer nor the distributor will assume any responsibility for the
damages produced to the equipment during its installation or damages to persons suffe-
red by the improper use of the electric connection. The tension should be 220 V, 50 Hz
±10%.
Version 2 February 2015 Instruction manual 5063xxx1
ENGLISH
Page 15