Manuales relacionados para Techne Tecal 650S
Resumen de contenidos para Techne Tecal 650S
- Página 1 Tecal 650S Calibrators Operator's Manual Issue 7 Date of issue: 3rd May 2005 Techne is a trademark © Techne, 2003...
-
Página 3: Tabla De Contenido
T E C A L 6 5 0 S O P E R A T O R ’ S M A N U A L CONTENTS Tecal Calibrator Operator’s Manual page SAFETY AND INSTALLATION English Français Deutsch Español THE CALIBRATOR Applications Warning Specification... - Página 4 T E C A L 6 5 0 S O P E R A T O R ’ S M A N U A L PAGE 2...
- Página 5 T E C A L 6 5 0 S O P E R A T O R ’ S M A N U A L NOTES PAGE 3...
-
Página 6: English
Servicing under this Techne have taken great care in the design of these units guarantee should be obtained from the supplier. to protect operators from hazards, but users should pay... -
Página 7: Français
Garantie combustibles risquent de prendre feu. Techne a apporté un soin tout particulier à la conception L’appareil est garanti contre tout défaut ou vice de de ces appareils de façon à assurer une protection fabrication pour la durée figurant sur la carte de garantie,... -
Página 8: Deutsch
Alle Benutzer von Techne Geräten müssen Zugang zu enthaltenen Beschreibungen und Spezifikationen, behält der entsprechenden Literatur haben, um ihre Sicherheit sich Techne hiermit das Recht vor, Änderungen an den zu gewähren. Geräten bzw. an einzelnen Geräteteilen durchzuführen. Es ist wichtig, daß diese Geräte nur von entsprechend Diese Gebrauchsanleitung wurde ausschließlich dazu... -
Página 9: Español
Cuando haya finalizado el calentamiento de muestras, Techne ha puesto gran cuidado en el diseño de estos recuerde que las piezas del equipo, tales como tubos, aparatos para proteger al usuario de cualquier peligro;... -
Página 10: The Calibrator
HIGH TEMPERATURES ARE DANGEROUS: they can cause serious burns to operators and ignite combustible material. Techne have taken great care in the design of these units to protect operators from hazards, but operators should pay attention to the following points: •... -
Página 11: Specification
T E C A L 6 5 0 S O P E R A T O R ’ S M A N U A L Specification The figures stated in the specification are as measured 0-50 mm from the base of the well of the insert, using an SPRT, at the time of calibration. -
Página 12: Packing
The packing comprises; the unit in the soft carrying case packed with foam into an outer cardboard box. Techne accepts no responsibility for damage incurred unless the unit is correctly packed and transported in this way. -
Página 13: When You Switch On
T E C A L 6 5 0 S O P E R A T O R ’ S M A N U A L WHEN YOU SWITCH ON When you first switch on, the display will show the edition of the software which your unit uses. - Página 14 T E C A L 6 5 0 S O P E R A T O R ’ S M A N U A L The DOWN ARROW Button ∇ ∇ ∇ ∇ ∇ When the SET temperature button is held down and the DOWN ARROW button is pressed, the set temperature is decreased.
-
Página 15: Setting The Units For Temperature
T E C A L 6 5 0 S O P E R A T O R ’ S M A N U A L Over-Temperature Indicator If the unit should, for any reason, exceed the temperature set for the over- temperature cutout (see page 15), the over-temperature indicator will light. -
Página 16: Cooling Probe
T E C A L 6 5 0 S O P E R A T O R ’ S M A N U A L Cooling Probe Operating temperatures below ambient can be achieved by using the cooling probe with a chilled water circulator. The cooling probe is supplied as an accessory and can be used in an insert with a 3/8"... -
Página 17: Rs232 Serial Interface
T E C A L 6 5 0 S O P E R A T O R ’ S M A N U A L RS232 SERIAL INTERFACE The calibrator may send data logging information to an IBM PC or compatible computer by connecting the unit and the PC via an RS232 cable, and installing the "Calsoft"... -
Página 18: Technical Information
The insert must be removed from the unit and packed separately within the case. Techne accept no responsibility for damage to units which are not properly packed for shipping: if in doubt, contact your supplier. -
Página 19: Replacement Parts
T E C A L 6 5 0 S O P E R A T O R ’ S M A N U A L Fuses If neither the power light nor display (on the front panel) is lit, one of the two fuses may have blown. -
Página 20: Accessories
T E C A L 6 5 0 S O P E R A T O R ’ S M A N U A L Accessories Part Nº Description FDB00CP Cooling Probe FCAL232 CALSOFT PC software kit Inserts Inserts are made from aluminium or aluminium-bronze and must be ordered separately from the calibrator.