Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
Mounting and removing the
dustbag (fig. B - D)
Warning! Do not use the appliance without
the dustbag.
Mounting the dustbag
The dustbag and the dustbag holder must be
properly mounted in order to close the cover
of the dustbag compartment.
•
Keep the release button (16) pressed and
open the cover (17) (fig. B).
•
Remove the dustbag holder (19) from the
dustbag compartment (6).
•
Insert the dustbag (20) into the slots (21)
of the dustbag holder (19) (fig. C1). Slide
the dustbag (20) to the end of the dustbag
holder (19) (fig. C2).
•
Insert the dustbag holder (19) into the slot
(22) of the dustbag compartment (6) (fig. D1).
Push the dustbag holder (19) until the
dustbag (20) is locked by the dustbag lock
(24) (fig. D2).
•
Close the cover (17) until the release button
(16) clicks into place. Make sure that the
hole (23) in the dustbag (20) aligns with the
hose connection (18).
Removing the dustbag
•
Keep the release button (16) pressed and
open the cover (17).
•
Remove the dustbag holder (19) from the
dustbag compartment (6).
•
Remove the dustbag (20) from the dustbag
holder (19).
•
Insert the dustbag holder (19) into the slot
(22) of the dustbag compartment (6).
•
Close the cover (17) until the release button
(16) clicks into place.
Mounting and removing the hose
(fig. E)
•
To mount the hose (7), insert the hose outlet
(25) into the hose connection (18) until the
release buttons (26) click into place.
•
To remove the hose (7), keep the release
buttons (26) pressed and pull the hose
outlet (25) from the hose connection (18).
Mounting and removing the tube
(fig. F)
•
To mount the tube (8), insert the hose inlet
(27) into the tube outlet (28).
•
To remove the tube (8), pull the hose inlet
(27) from the tube outlet (28).
Mounting and removing the
suction nozzle (fig. G)
The suction nozzle (11) can be mounted to the
extension tube (9).
•
To mount the suction nozzle (11), insert the
tube inlet (29) into the tube connection (30).
•
To remove the suction nozzle (11), pull the
tube inlet (29) from the tube connection (30).
Mounting and removing the
crevice nozzle (fig. F & G)
The crevice nozzle (15) can be mounted to
the hose (7) or to the extension tube (9).
•
To mount the crevice nozzle to the hose (7),
insert the hose inlet (27) into the crevice
nozzle (15).
•
To mount the crevice nozzle to the extension
tube (9), insert the tube inlet (29) into the
crevice nozzle (15).
•
To remove the crevice nozzle, pull the
crevice nozzle (15) from the hose inlet (27)
or the tube inlet (29).
Use
Unwinding and rewinding the
mains cable (fig. A)
The mains cable rewind button (2) can be
operated by hand or foot.
Caution!
-
Do not unwind or rewind the mains cable
while the appliance is switched on.
-
Always hold the mains plug to unwind the
mains cable. Never pull the mains cable.
•
Before use, hold the mains plug and unwind
a sufficient length of the mains cable from
the back of the appliance.
13
Publicidad
Tabla de contenido
