AccuLite Caribe Guia De Inicio Rapido

Important Safeguards:
WARNING – When using electrical equipment, basic safety precautions should always be used including the following:
This product must be installed in accordance with the applicable installation code by a person familiar with the construction and
operation of the product and the hazards involved.
READ AND FOLLOW ALL SAFETY INSTRUCTIONS
Mark means lamp contains mercury.
Hg Hg
Follow disposal laws.
See www.lamprecycle.org
❶
Disconnect Power
• Always disconnect power during installation and maintenance.
❷
Mount Luminaire
STEM MOUNT
FloodLux™ (illustrated - right)
AccuFlood™
Caribe (illustrated - left)
• Thread the stem into 1⁄2" hub. (junction
box and cover are supplied by customer)
• Aim Fixture.
• Ensure that the teeth of the stem knuckle
are in alignment,.
• Tighten knuckle bolt and lock nut.
Do not over tighten the knuckle bolt.
❸
Connect Wiring
• Loosen the cover bolt(s) to open hinged
door assembly.
• Remove the reflector to access wiring
chamber.
• Check Voltage
Ensure correct lead is used on multi-
voltage ballasts.
• Connect wires to proper voltage.
• Individually cap all unused leads.
lasts.
• Replace reflector.
❹
Install Lamp
• Observe the lamp manufacturers
recommendations and restrictions.
➎
Close Door Assembly
• Secure all bolts
®
Technical Support: 888 / 387-2212
1300 S Wolf Road, Des Plaines, Illinois, 60017 / 219 Shoemaker Street, Kitchener, Ontario, N2E 3B3 / 220 Chrysler Drive, Brampton, Ontario L6S 6B6
Caribe / AccuFlood
"CF", "EF'" "FLS" & "RBF" Floodlight Installation Instructions
YOKE MOUNT
AccuFlood™ (illustrated : FLS & EF Series)
Caribe
• Adjust horizontal aiming and secure fixture
yoke to mounting surface.
• Loosen the trunnion bolts and adjust the
vertical aiming. (Note: remove the decorative
bolt cover on 250W & 400W Caribe models.)
• Tighten the trunnion bolts. (Replace the
decorative cover on Caribe models).
❸
Connect Wiring
• Loosen the cover bolt(s) to open hinged door
assembly.
• Remove the reflector to access wiring chamber.
• Check Voltage
Ensure correct lead is used on multi-voltage
ballasts.
• Pull approved cable through cable connector
and tighten connector
• Connect wires to proper voltage.
• Individually cap all unused leads.
• Replace reflector.lasts.
❹
Install Lamp
• Observe the lamp manufacturers
recommendations and restrictions.
➎
Close Door Assembly
• Secure all bolts
/ FloodLux
™ ™
SLIPFITTER MOUNT
Caribe ( illustrated - right)
AccuFlood™ (illustrated - EF Series - left)
• Slide slip fitter over top of pole tenon.
• Adjust the horizontal Aiming and tighten slip fitter bolts.
• Remove cover from slipfitter pulling chamber.
• Adjust the vertical aiming.
• Ensure that the teeth of the slip fitter are in alignment,
then tighten the knuckle bolt.
Do not over tighten the knuckle bolt. (Do not exceed
30 Ft/Lbs maximum torque).
❸
Connect Wiring
• Loosen the cover bolt(s) to open hinged door assembly.
• Remove the reflector to access wiring chamber.
• Check Voltage
Ensure correct lead is used on multi-voltage ballasts.
• Pull supply cable
• Connect wires to proper voltage.
• Individually cap all unused leads.
• Replace reflector.
❹
Install Lamp
• Observe the lamp manufacturers recommendations and
restrictions.
➎
Close Door Assembly
• Secure all bolts
SAVE THESE INSTRUCTIONS
Z-12009
Rev 3 15/07/2007
lasts.