Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
Mounting and removing the tube
(fig. A)
•
To mount the tube, insert the hose (8) into
the tube (9).
•
To remove the tube, pull the hose (8) from
the tube (9).
Mounting and removing the
suction nozzle (fig. A)
The suction nozzle can be mounted to the
extension tube.
•
To mount the suction nozzle, insert the
extension tube (10) into the suction nozzle
(12).
•
To remove the suction nozzle, pull the
extension tube (10) from the suction nozzle
(12).
Mounting and removing the
crevice nozzle (fig. A)
The crevice nozzle can be used for vacuuming
in narrow and hard-to-reach places. The
crevice nozzle can be mounted to the hose or
to the extension tube.
•
To mount the crevice nozzle to the hose,
insert the hose (8) into the crevice nozzle
(16).
•
To mount the crevice nozzle to the
extension tube, insert the extension tube
(10) into the crevice nozzle (16).
•
To remove the crevice nozzle, pull the
crevice nozzle (16) from the hose (8) or the
extension tube (10).
Mounting and removing the
upholstery nozzle (fig. A)
The upholstery nozzle can be used for
vacuuming upholstery, curtains and other items
made of fabric. The upholstery nozzle can be
mounted to the hose or to the extension tube.
•
To mount the upholstery nozzle to the hose,
insert the hose (8) into the upholstery
nozzle (17).
•
To mount the upholstery nozzle to the
extension tube, insert the extension tube
(10) into the upholstery nozzle (17).
•
To remove the upholstery nozzle, pull the
upholstery nozzle (17) from the hose (8) or
the extension tube (10).
Use
Unwinding and rewinding the
mains cable (fig. A)
The mains cable rewind button (2) can be
operated by hand or foot.
Before you proceed, we would like you to
focus your attention on the following notes:
-
Do not unwind or rewind the mains cable
while the appliance is switched on.
-
Always hold the mains plug to unwind the
mains cable. Never pull the mains cable.
•
Before use, hold the mains plug and
unwind a sufficient length of the mains
cable from the back of the appliance.
•
After use, press the mains cable rewind
button (2) to rewind the mains cable back
into the appliance. Manually guide the
mains cable to make sure that it does not
swing back. Make sure that the mains plug
is correctly located.
Adjusting the length of the tube
(fig. A)
•
Keep the locking knob (19) pressed and
slide the extension tube (8) to the required
position.
•
Release the locking knob (19).
Adjusting the suction nozzle (fig. A)
The floor surface selector can be set to adjust
the suction nozzle to the required floor surface.
The floor surface selector can be operated by
hand or foot.
•
For vacuuming on laminates, tiles, etc.,
press the corresponding part (A) of the
floor surface selector (13).
•
For vacuuming on carpets, press the
corresponding part (B) of the floor surface
selector (13).
Switching on and off (fig. A)
The on/off button can be operated by hand
or foot.
•
To switch on the appliance, press the
on/off button (1).
•
To switch off the appliance, press the
on/off button (1) again.
12
Publicidad
Tabla de contenido
