Publicidad
Idiomas disponibles
Idiomas disponibles
Charging the DeWALT Li-ion Battery
E
1.
If the 12V MAX Li-ion battery pack is attached to the laser,
remove it (Figure
• Rotate the laser so it is easier to access the battery pack
(Figure
#1).
D
• While pressing down on the release button on the battery
pack (Figure
D
from the laser (Figure
• Pull the battery pack the rest of the way up and out of the
laser (Figure
D
2.
Plug the charger cord into an electrical outlet.
3.
Slide the battery pack into the charger until it snaps in place
(Figure
#1). On the charger, the left indicator light will flash
F
to let you know the battery is being charged (Figure
4.
After the battery is fully-charged (the indicator light on the
charger no longer flashes), press and hold the release button
on the battery pack (Figure
the charger (Figure
5.
Slide the battery pack down in the laser until it snaps in place
(Figure
#5).
F
Installing New AA Batteries
CAUTION:
The AA Starter Pack is designed specifically for use
with DeWALT 12V compatible laser products and
cannot be used with any other tools. Do not attempt
to modify the product.
1.
If the AA Starter Pack is attached to the laser, remove it (Figure
).
D
• Rotate the laser so it is easier to access the Starter Pack
(Figure
#1).
D
• While pressing down on the release button on the Starter
Pack (Figure
D
from the laser (Figure
• Pull the Starter Pack the rest of the way up and out of the
laser (Figure
D
2.
On the AA Starter Pack, lift up the latch to open the battery
compartment cover (Figure
3.
Insert four new, high-quality, name brand AA batteries, making
sure to position the - and + ends of each battery as noted inside
the battery compartment (Figure
8
).
D
#2), pull the battery pack up to unlock it
#3).
D
#4).
#3) and slide the pack out of
F
#4).
F
#2), pull the Starter Pack up to unlock it
#3).
D
#4).
#1 and #2).
E
#3).
E
4.
Push the battery compartment cover down until it snaps in
place.
5.
Slide the Starter Pack down in the laser until it snaps in place
(Figure
#4).
E
Viewing the Battery Meter on the Keypad
When the laser is ON, the battery meter on the keypad (Figure
#3) indicates how much power remains. Each of the four LEDs
on the battery meter represents 25% of the power.
• The bottom LED will illuminate and flash when the battery
level is low (below 12.5%). The laser may continue to operate
for a short time while the battery power continues to drain,
but the beam(s) will quickly dim.
• After fresh batteries are installed in the AA Starter Pack, or
the 12V MAX Li-ion battery is charged, and the laser is turned
#2).
F
ON again, the laser beam(s) will return to full brightness and
the battery indicator level will indicate full capacity.
• If all 4 LEDs on the battery meter remain ON, this indicates
that the laser is not fully powered OFF. When the laser is not
in use, make sure the Power/Transport Lock switch is placed
to the LEFT to the Locked/OFF position (Figure
Turning the Laser On
1.
Place the laser on a smooth, flat surface.
2.
Slide the Power/Transport Lock switch to the right to the
Unlocked/ON position (Figure
3.
Press each button on the keypad (Figure
each laser beam setting.
• Press
#3a), a second time to display a vertical laser line (Figure
#3b), a third time to display a horizontal line and a
A
vertical line (Figure
displaying laser lines.
• Press
(Figure A #3d) and a second time to stop displaying dots.
• You can use
and lines. For example, if you press
once, the laser will display cross lines and two dots
(Figure
A
#1b).
A
once to display a horizontal laser line (Figure
#3c), and a fourth time to stop
A
once to display dots above and below the laser
and
together to display laser dots
#3e).
A
#1a).
A
#3) to test
A
A
three times and
Publicidad
