Installation Considerations - Rockford Fosgate ELEMENT READY COLOR OPTIX M1WL-65MB Guia De Inicio Rapido

Tabla de contenido

Publicidad

Installation
(1)
(2)
(3)
(4)
(5)
(6)
Contents
• (1) Pair Moto Can Speakers
• (1) Pair Universal Clamps
• (4) Grommets
• (4) Safety Inserts for Screw
Clamp
• (2) 1" to 1.6" Rubber Clamp
Inserts and Stainless
Hardware
• (2) 1.6" to 2" Rubber Clamp
Inserts and Stainless
Hardware

Installation Considerations

Before beginning any installation, follow these simple rules:
1. Be sure to carefully read and understand the instructions
before attempting to install these speakers.
2. For safety, disconnect the negative lead from the battery
prior to beginning the installation.
3. For easier assembly, we suggest you run all wires prior to
mounting your speakers in place.
4. Use high quality connectors for a reliable installation and
to minimize signal or power loss.
5. Think before you drill! Be careful not to cut or drill into gas
tanks, fuel lines, brake or hydraulic lines, vacuum lines or
electrical wiring when working on any vehicle. If installation
in a boat, take care not to cut or drill through the main hull.
6. Never run wires underneath the vehicle. Running the wires
inside the vehicle or hull area provides the best protection.
7. Avoid running wires over or through sharp edges. Use
rubber or plastic grommets to protect any wires routed
through metal, especially the firewall.
6
1 - BLACK (Speaker Negative, 18 AWG)
2 - YELLOW (12V + Input, 22 AWG)
3 - RED (Speaker Positive, 18 AWG)
4 - GREEN (Ground Input, 22 AWG)
5 - RED (Ground Input, 22 AWG)
6 - BLUE (Ground Input, 22 AWG)
Included with speakers
Connector is DEUTSCH
/Amphenol style
illus.-4.3
• (2) Speaker Harnesses
• (1) Pair Sport Grills
(Installed on M1)
• (1) Pair Sport Grills
(Installed on M2, not
available on M1)
• (1) Allen Bit For Speaker
Removal For Rotation
• (1) Safety Torx Wrench
DT06-4S
Mounting
1. Determine where the speakers will be mounted. Be sure
that the mounting location has sufficient clearance in all
direction for the speaker to swivel; conduct a full rotation to
ensure there is not obstruction.
2. Mark the location where the wiring will come out near
where the Moto can will be mounted. Drill a 7/16" hole in
the location you marked for your wire exit. The wiring will
connect to the rear of the can
3. Insert the supplied grommet and feed the wire harness
through. Be sure to observe proper polarity when
connecting the wires. The speaker harness's negative wire
is the BLACK 18 AWG wire and the Positive is the RED 18 AWG
wire in the 6 pin connector
4. Remove the plastic cover over the safety torx bolt to allow
access to loosen/tighten the wake can. Do this to adjust
the angle of the wake can, then tighten the safety torx bolt
to make sure it does not move. Replace plastic cover over
safety torx bolt
5. Rotate the medalion on the rear of the wake can to look like
the image in
the medalion. You will hear/feel a clicking when you rotate
it.
6. If you need to rotate the speaker, remove the (6) screws
holding th speaker and grill on. Pull the speaker slightly
towards you and rotate it until it looks like
predrilled holes to reinstall the speaker
14"
(355mm)
15"
(380mm)
.
illus.-4.2
.
illus.-4.3
.
illus.-3.3
. This can be turned left or right to align
illus.-3.2
illus.-3.1
illus.-4.4
. Use the
illus.-1.1
.

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Element ready color optix m2wl-65mb

Tabla de contenido