JAQUE T300 Manual De Instrucciones

IRAM:3687/ EN:1125 Compliant
INSTRUCTION MANUAL
LINE T300/ T395
This panic device manual must be provided to user.
1
1- To mark mechanism height (h), mount bar at a height
between 36" (900mm) and 43" (1100mm) from floor. In
areas where evacuees may be mostly children, device may
be installed at a lower height.
4
4-Place the provided template into position, mark and drill
1/8" (3.25 mm) holes on the inside face of the door on the
latch door stile. If outside trim is added, drill 1/2" (12mm)
through holes.
7
7 - Use a saw to cut rail case, bar and center rod to the
extent necessary in the places indicated in the illustration
(always same measure (a) in the 3 cuttings). Then place
again rear scissor, mounting bracket, center rod and grub
screws in the opposite direction to the one shown in 6.
10
10- Dogging system: to undogg the push bar, turn a flat
screwdriver 90° clockwise; to dogg it, turn tool 90°
anticlockwise.
13
13 –
13 – Check the smooth functioning of the door. If necessary,
use strike slots to adjust the position of strike plate with
closed door. The door must open SMOOTHLY.
Front part
MECHANISM ASSEMBLY (SINGLE LEAF)
2
2-Center strike plate with line, mount and mark holes. Drill holes on
frame with a #25 (3.75 mm) drill bit. The centers of the holes must
be positioned at 5/8" (15 mm) 'b' distance from frame inside edge.
5
5- To undogg the push bar procced as shown in 10. If necessary,
reduce rail case length. For this, remove screws from end cap and
remove it, and the front nylon cover as well; slide push bar
backwards and then remove rear nylon cover. To lift bar, lean it as
shown in the illustration and remove it pushing forward.
8
8- Mount rail case on door and center it. Mark and drill holes on
mounting bracket with a 1/8"(3.25mm) drill bit. Place rail case on
door, fix case screws and mounting bracket screws. Use a Phillips
screwdriver to tighten screws.
11
11- Follow single leaf door steps to install the first lock on main door,
but fit front strike plate flush with the edge of the secondary door.
Use template provided to mark and repeat steps 1, 4, 5, 6, 7 and 8 to
install the second lock on the side of the secondary leaf
Panic device projection category 2 (2 1/2"/64mm)
Door application field: Single and double doors
Max. Weight: 440Lb.(200kg.)
Max. Width: 4'(1220mm)
Max. Height: 8'(2440mm)
Temperature: 14°F to 140°F (-10°C a 60°C)
Line T 395: designed for fire doors, 90min. fire
resistant.
Blincer S.R.L Calle 127 (Ombu) 1444- San Martin- Prov. Bs.As. (Argentina)
Phone: +5411 4712 5005 website: www.blincer.com
DESIGNATION OF PARTS
3
3- Secure strike plate on frame with screws and washers in the
order as shown in the illustration. Mount strike plate on its
support face according to Step 2. Use the accessories provided,
if necessary.
6
6- Use a 2.5mm Allen wrench to loosen grub screws holding
levers linking rod, and remove the mounting bracket and the
rear lever using the rail case track for this.
9
9 - Place bar again in the opposite direction to the one
shown in number 5. Place bar covers, end cap and cap as
well as the screws. Use a Phillips screwdriver to tighten
screws (see images A and B above).
12
12- Insert latch bolt in secondary leaf rail case until the latch
screw head is visible and remove it with Phillips screwdriver.
Then, remove detachable latch bolt.
MANUFACTURER´S SPECIFICATIONS
"The safety features of this product comply with EN 1125
and IRAM 3687. Alterations other than the ones specified in
these instructions are forbidden".
REMARKS: For double leaf doors, see T291 assembly
instructions.
Rear part
I301-65 Rev.03 (04-2020)