Publicidad
EFPW-W2
Wireless wall switch 2 buttons
+
EFPW-W2 : Switch
CR2430
1x
1x
2x
1. Changing the battery
1
2. Select use mode
The wireless switches have 2 working modes (by default, mode1):
Mode 1 : 2 channels (double switch)
Control all in 1 button : On/O , Open/Close, Dimming* +/-
ON/OFF
ON/OFF
or
Mode 2 : 1 channel ( single switch )
Control with 2 buttons : LEFT button to turn o , close or dimming – *
Right button to tun on, open or diming + *
OFF
or
ON
* Keep pushing the button, the brightness starts to inis associated with dimmer module crease/ decrease,
release to stop.
**This option is only available when remote
How to change mode :
Take out the front pannel from the switch.
Push the "E" Button and at same time push one of the switch button.
The blue LED will ash :
• 1x for mode 1
• 2x for mode 2
E
3 . Linking the switch with an Edisio receiver
EN
This product is compatible with all Edisio peripherals operating under the 868MHz radio
protocol, and with the DiO Smart Home main unit for control through your smartphone.
Using the DiO main unit, you can control your home wherever you are through your
smartphone and also make your wireless switch compatible with DiO peripherals. For
more information visit: www.getdio.com.
3.1. Linking with light or shutter module or plug
R button
Mode 1
1x
2x
2x
Push one the R button of the Edisio
receiver.
2
+
Within 10 seconds, push the «N°1» button
of the wall switch.
CR2430
N°1
Within 10 seconds, push again the R
button of receiver to con rm the link.
ON/OFF
or
Follow the same process to link the "N°2"
button.
R
3.2. Delete the link between the switch and the receiver
Push during 5 seconds the R button of the Edisio receiver.
Within 10 seconds, push the button of wall swich to remove.
Within 10 seconds, push again the R button of receiver.
3. Associar a um periférico Edisio
R button
R button
Mode 2
Push one the R button of the DiO 2.0
receiver.
R
R
Within 10 seconds, push the «ON» button
of the wall switch.
ON
Within 10 seconds, push again the R
button of receiver to con rm the link.
R
R
Follow the same process to set up the
«OFF» button of the switch.
R
R
N°2
OFF
4. Technical speci cations
Frequency: 868.3 MHz
Protocol: Edisio
Transmission range: 150 m (in free eld)
Indoor use (IP20). Do not use in a damp environment.
Lithium battery: CR2430 3V (included)
Working temperature: -5°C +45°C
Dimensions: 85 x 85 x 11 mm
5. Supplementing your installation
Supplement your installation with Edisio solutions to control your heating, lighting, roller
shutters or garden.
Easy, high-quality, scalable and economical...learn about all of the Edisio solutions at
www.edisio.com.
Recycling
R
In accordance with European WEEE directives (2002/96/EC) and directives concerning accumulators
(2006/66/EC), any electrical or electronic device or accumulator must be collected separately by a local system
specialising in the collection of such waste. Do not dispose of these products with ordinary waste. Check the
regulations in force. The logo shaped like a waste bin indicates that this product must not be disposed of with
household waste in any EU country. To prevent any risk to the environment or human health due to
uncontrolled scrapping, recycle the product in a responsible manner. This will promote the sustainable use of
material resources. To return your used device, use the return and collection systems, or contact the original
dealer. The dealer will recycle it in accordance with regulatory provisions.
Declaration of conformity
Smart Technology SA declares that the devices EFPW-W2 is conformed with the requirements and provisions
of Directive RED 2014/53/EU. The complete text of the EU declaration of conformity is available at the
following Internet address: www.chacon.be/en/conformity
Hotline
www.edisio.com/contact-us/
4. Características técnicas
V1.0 190625
Publicidad
