Veiligheidsvoorschriften - glemgas GHBS97IX Manual Del Usuario

months one must wash the anti-grease filters by hand
using non-abrasive neutral liquid detergents or in the
dishwasher at low temperatures and on short cycles.
- After a few washes, colour alterations may occur. This
does not give the right to claim their replacement.
• The active carbon filters are used to purify the air
that is sent back into the room and its function is to
mitigate the unpleasant odours produced by cooking.
- The non-regenerable active carbon filters must be
replaced at least every 4 months. The saturation of the
active charcoal depends on the more or less prolonged
use of the appliance, on the type of kitchen and on the
frequency with which anti-grease filter is cleaned.
- Regenerable active charcoal filters must be washed
by hand, with non abrasive neutral detergents, or
in the dishwasher at a maximum temperature of
65°C (the washing cycle must be complete without
dishware). Remove excess water without damaging
the filter, remove the plastic parts, and let the mat
dry in the oven for at least 15 minutes approximately
at a maximum temperature of 100°C. To keep the
regenerable charcoal filter functioning efficient this
operation must be repeated every 2 months. These
must be replaced at least every 3 years or when the
mat is damaged.
• Before remounting the anti-grease filters and the
regenerable active charcoal filters it is important
that they are completely dry.
• Clean the hood frequently, both internally and
externally, using a cloth dampened with denatured
alcohol or neutral liquid detergents that are non
abrasive.
• The lighting .system is designed for use during
cooking and not for the prolonged general lighting
of the room. The prolonged use of the lighting system
significantly decreases the average duration of the
bulbs.
• If the appliance is equipped with courtesy lights it is
possible to use them for general room lighting for a
prolonged amount of time.
• Attention: the non compliance with the hood
cleaning warnings and with the replacement and
cleaning of the filters entails risk of fires. One therefore
recommends keeping to the suggested instructions.
• Replacing halogen light bulbs (Fig.6A):
To replace the halogen light bulbs Z, remove the
glass pane
C using a lever action on the relevant cracks. Replace
the bulbs with new ones of the same type. Caution:
do not touch the light bulb with bare hands.
• Replacing LED lamps (Fig.6B):
If the appliance version is with LED lamps, the
intervention of a specialised technician is necessary
to replace them.
• Control (Fig.7):
NOTE: with this command it is also possible to control
the appliance using a remote control, to be requested
as an accessory.
A Button = Switches the hood on/off. The equipment
switches on at the 1st speed.
B Button = Decreases motor speed.
C Display = Shows the selected motor speed and timer
activation/intense speed/filter warning.
D Button = Increases motor speed.
Pressing the 4th speed button engages the intense
function for 6 minutes, then the equipment goes back
to working at the speed at which it was activated. Du-
ring this function, the number 4 flashes on the display.
- If you wish to deactivate the function before the 6
minutes, press the B button.
Attention! Some models only work up to the 3rd
speed and, therefore, do not have the intense function.
E Button = Pressing this button activates the Timer
function even with any of the 1-2-3 speeds engaged
(except the Intense function speed). When the Timer
function is active, the set speed must flash on the
display when the timer is activated.
After 15 minutes, at the end of the countdown, the
hood switches off (motor and any lights remain on).
If the intense speed is engaged, the Timer cannot be
activated.
- If you wish to deactivate the function before the 15
minutes, press the E button.
F Button = Switches the lights on/off.
• Anti-grease/active charcoal filters saturation:
- After 30 h of operation, when the C display flashes,
alternating the working speed with the letter F (i.e.
2 and F), this means that you need to wash the anti
grease filters.
- After 120 h of operation, when the C display flashes,
alternating the working speed with the letters C/F (i.e.
2 and C/F), this means that you need to wash or replace
the charcoal filters.
- Once you have repositioned the clean filter, you need
to reset the electronic memory with the hood on,
pressing the B button for about 3 seconds.
After that time, the letter E appears on the display
(reset confirmed) and the hood switches off.
• Mechanical control (Fig.8) the key symbols are
explained below:
A = LIGHT
B = OFF
C = SPEED I
D = SPEED II
E = SPEED III
T H E M A N U F A C T U R E R D E C L I N E S A L L
RESPONSIBILITY FOR EVENTUAL DAMAGES
CAUSED BY BREACHING THE ABOVE WARNINGS.
NEDERLANDS
ALGEMEEN
Lees aandachtig de inhoud van deze handleiding.
Hierin staan belangrijke aanwijzingen voor een
veilige installatie, gebruik en onderhoud. Bewaar de
handleiding om die later te kunnen raadplegen. Het
toestel werd ontworpen in een versie voor afzuiging
(evacuatie van de lucht naar buiten - Afb.1B) en voor
filtering (recirculatie van de lucht binnen - Afb.1A) of
met externe motor (Afb.1C).

VEILIGHEIDSVOORSCHRIFTEN

1. Opletten indien tegelijkertijd
een afzuigkap en een brander of
haard functioneren die afhanke-
- 19 -
NL