Important Safety Information - xybul FREEbul Guia De Inicio Rapido

For assembly by an adult (Keep this information for future reference)
IT IS RECOMMENDED TO WEAR PROTECTIVE GEAR (wrist pads, helmet, knee and
elbow pads) AND REFLECTORS.
PLEASE CHECK THE CONTENTS BELOW BEFORE USE:
A - Brake (x2)
B - Screw for Brake (x2)
C - Nut for Brake (x2)
D - Allen Keys (x2)
E - Axle for «learner» version wheels (x2)
F - Screw for «learner» version axle (x2)
G - «In line» version central axle (x6)
H - Nut for «In line» version central axle (x6)
TO GO TO « LEARNER » VERSION TO « IN LINE » VERSION :
1. First use the 2 Allen keys to remove the learner wheels at the rear. Gradually
loosen to remove the central axle, the screw, washers and axle (parts I, F, K, E)
that holds the 2 wheels.
2. Insert one of the removed wheels into the «in-line" skate frame, aligning
the holes. Using the additional nuts and screws supplied (sachet) in the
skate bag, insert axle G through the wheel and screw on from the other side
with nut H (N.B.: wheel axles G and E are not the same length. They are not
interchangeable. The "in line" version uses axles G, and the "learner" version
uses axles E ).
3. Screw tightly using the Phillips head screwdriver.
4. Do the same for the second wheel (Stages 2 and 3) The front wheel remains
in the same place, but you must check that it is screwed on tightly.
TO ADJUST THE SIZE OF THE ROLLER SKATE:
1
3 4
I - Central axle of «learner» version rear
wheels (x2)
J - Wheel (x6)
K - Washers (x8)
L - Roller skate frame (x2)
M - Roller skate shoe (x2)
N - Roller skate liner (x2)
O - Phillips head screwdriver (x1)
2
5 6
Locate the adjustment button that allows you to adjust the hard shell to fit 4
sizes (drawing 1).
Hold the rear of the wheels in one hand (just above the brake) and push (or
pull) the end of the shoe with the other hand (drawing 2).
The sizes are shown on the side of the shoe (drawings 3 to 6):
Position 27 = Size 27
Position 28 = Size 28
To change the brake unscrew from beneath the roller, remove the screw,
brake, put the new brake and tighten it.
IMPORTANT SAFETY FOR USE
TO BRAKE:
- Place one of the roller skates in front of the other.
- Press down gently on the heel to slow down.
- Take care not to lose your balance.
This needs a bit of practice – Pay attention because you might fall while
practicing.

IMPORTANT SAFETY INFORMATION

To reduce the risks of injuries due to roller skating:
1. These roller skates are for children aged 3 years and over.
2. Do not change the design of the roller skates as this could make them
unsafe.
3. For outdoor use only.
4. Check that the screws are tightened properly.
5. Do not use in snow, on wet or oily surfaces, on gravel, black ice, or on
unevenly paved surfaces.
7. Avoid steep slopes and maintain a slow speed.
8. Beginners must know the rules of roller skating and have prior training.
9. Learn to stop safely.
10. Do not use at night.
11. For use under adult supervision.
12. Ensure that the various materials are in good condition, and that the
conditions of use and maintenance are maintained.
13. Replace the wheels if they are worn or damaged.
14. Lubricate certain parts if necessary.
15. Adjust to the correct size and fit.
16. The product should be used with caution since skill is required to avoid falls
or collisions causing injury to the user or third parties.
REGULAR MAINTENANCE INCREASES THE SAFETY OF THE EQUIPMENT
17. The roller skates must be maintained and kept clean. You must regularly
check all the parts and replace damaged parts before using them again.
18. If the rollers jam or stick, the problem is probably caused by accumulated
dust or dirt. Replace them immediately.
19. The rollers and other spare parts can be bought in a local specialist store.
20. Lubricating the rollers – the metal ball bearings require maintenance.
roller skates. By lubricating them with non-stick oil or a lubricant especially for
bearings, you can use a dry cloth to ensure there is not residual excess. Thus
you will lengthen the life of the bearings. N.B.: using a stick lubricant attracts
dust and increases the risks of wear and tear.
HAVE FUN AND TAKE CARE!
Position 29 = Size 29
Position 30 = Size 30